Gentex HGU-55/P Скачать руководство пользователя страница 30

Страница: 30 / 70

Chapter 2: Helmet Preparation and Operation

2-4 3 Operating Visor

Operate the visor as follows:

1. Referring to

Figure 2-31

, grasp the

visor in the center and pull the visor

slightly away from the helmet.

2. Move the visor up or down. When

the visor is up, ensure that the top

edge of the visor is against the two

bump stops.

3. As necessary, adjust the visor straps

so that the visor is centered over the

nose. Ensure that the visor is snug

enough. The visor should not slide

freely up and down. There should be

enough resistance to require pulling

the visor away from the helmet to

raise or lower it.

NOTE:

When the visor is up, you

can attach the visor cover by

pressing the hook fasteners on the

cover to the pile fastener on the

visor.

2-4 4 Connecting Mask Microphone
Cord to Helmet Connector

With the helmet donned and properly

adjusted, do the following:

1. Don the mask. Check the mask

for proper position and tension in

accordance with applicable oxygen

mask technical orders. Check the

interface between the visor and the

mask. Adjust the mask straps as

required.

2. Connect the mask cord to the helmet

connector, shown in

Figure 2-32

NOTE:

To remove the mask cord from the

helmet connector, pull firmly on the cord

plug.

VISOR COVER

INSTALLATION

Cover

Bump stop

(both sides)

Strap

(both sides)

Figure 2-31. Operating Visor

Figure 2-32. Connecting Mask Cord

Mask

cord

Helmet

connector

Содержание HGU-55/P







































































Результаты поиска

Содержание HGU-55/P

Отзывы:

Похожие инструкции для HGU-55/P

Бренды по названию

Популярные бренды

Gentex HGU-55/P, Инструкция по эксплуатации и техническому обслуживанию с иллюстрированным перечнем деталей

Результаты поиска

Содержание HGU-55/P

Отзывы:

Похожие инструкции для HGU-55/P

Бренды по названию

Популярные бренды