General 90-050 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

General 90-050 Скачать руководство пользователя страница 9

6. Re-install the table insert

.

7. Insert the table aligning pin

in the hole at

the side of the table.

8. Re-install the extension table and re-attach the

stop-screw

.

Store the miter gauge on the supplied bracket on the
stand as shown.

bottom

view

MITER GAUGE

Attach the power cord brackets

to the rear of

the saw, as shown using the 2 Phillips head screws

.

To prevent damage, stow the cord by wrap-

ping it onto the brackets whenever the saw is not
in use.

Remove 4 phillips screws

from machine body. Install

the work light

and the power cord to the machine

body by using 4 phillips screws and tighten.

The worklight uses a standard 110V household light-
bulb, 60 Watts - Not Included.

INSTALLING POWER CORD STORAGE BRACKETS

ATTACHING THE WORK LIGHT

REMOVING & INSTALLING THE BLADE

Before replacing or adjusting the blade, make sure the switch is in the “OFF” position and that the power cord is unplugged.

1. To remove blade, release blade tension by turning

the blade tension knob

counter-clockwise until

it stops.

2. Remove the table insert and table aligning pin.

3. Open

upper and

lower wheel

cover

doors.

4. Loosen the 2 Phillips screws

and remove the

upper blade guard

.

Note: Extension table must be removed when removing/installing the blade. See Step 2 & 8 in INSTALL THE BANDSAW TABLE, pg. 8 & 9.

5.

Remove the blade

from the upper and lower

blade guides. Carefully pull the blade from the
side slot

and from the wheels

.

6.

Swing the left side of the blade toward you, turning
the blade so it will fit through the slot

in the table

and remove.

9

«
...
7
8
9
10
11
...
»

Содержание 90-050

























Отзывы:

Нет отзывов