General 90-050 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

General 90-050 Скачать руководство пользователя страница 7

ASSEMBLY INSTRUCTIONS

ASSEMBLING THE STAND

1.

Lay the top plate

upside down on a flat sur-

face.

2.

Attach the 4 legs

to the outside of top plate

using 4 carriage bolts, washers, and nuts

.

Note: Do not tighten hex nuts until all fasteners
are attached.

3.

Attach 2 long brackets

and 2 short brackets

to the inside for the legs, using carriage bolts

,washers, and nuts

.

4.

Place the foot pads

on the bottom of each

leg.

5.

Place the stand on a flat surface to square it up
and finally tighten all the nuts.

The bandsaw is heavy. The help of an assis-
tant will be needed to lift the bandsaw.

1.

Lift the saw body

with the help of an assistant

and place it on the stand.

2.

Using 4 long hex head bolts

, 8 flat washers

, and 4 hex nuts

, secure the bandsaw to

the stand and tighten all mounting bolts.

ATTACHING THE BANDSAW TO STAND

ATTACHING DUST PORT

1.

Remove the bolts and washers from the dust
port.

2.

Open the lower wheel cover door

.

3.

Attach the dust port

to the edge of the door

using the same hex head bolts and washers

.

4.

Tighten the bolts and close the door.

7

The dust port has a 2-1/2” opening to accommodate
connection to a dust collector (not included).

«
...
5
6
7
8
9
...
»

Содержание 90-050

























Отзывы:

Нет отзывов