General 90-050 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

General 90-050 Скачать руководство пользователя страница 13

LOWER BLADE GUIDES

Note: The lower blade guides and support bearings
should always be adjusted after the blade is tensioned,
tracking is adjusted, and the upper blade guides and
upper support bearings are properly adjusted.

1.

Loosen both front hex socket screws

with a hex

wrench and move the bearings

as close to the sides

of the blade

as possible without pinching it.

2.

Using the feeler gauge, measure the spaces between
the guide and the blade. Adjust to 0.02”.

3.

Tighten the hex screws

and loosen the side hex sock-

et screw

. Move the guide support bracket

in or out

until the guides are at least 1/32” behind the saw teeth.
Tighten the screw.

LOWER SUPPORT BEARING

1.

Loosen the bearing hex socket screw

with the hex

wrench.

2.

Move the blade support bearing shaft

in or out until

the support bearing

is 1/64” behind the saw blade.

3.

Tighten the bearing hex socket screw

.

PULLEY ALIGNMENT

Note: The pulley alignment has been pre-set and verified
at the factory and should not need re-adjustment. If
adjustment is needed or the belt needs replacing:

1.

Place a straight edge in the front groove of both pul-
leys, behind the blade wheel.

2.

Turn the set screw

in the side of the motor pulley

to

loosen the pulley on the shaft.

3.

Adjust the pulley in or out on the shaft

to align the

edges of the two pulleys.

4.

When aligned, re-tighten the set screw on the side of the
motor pulley.

13

«
...
11
12
13
14
15
...
»

Содержание 90-050

























Отзывы:

Нет отзывов