General Standards Corporation PCI-DIO24PMC-DIO24PCI-DIO24-GD1 Скачать руководство пользователя страница 27

Страница: 27 / 29

DIO24, User Manual

Local Interrupt must be enabled for USC/FIFO interrupts.

D12

Retry Abort Enable (Unused)

D13

PCI Doorbell Interrupt Status.

D14

PCI Abort Interrupt Status

D15

PCI Local Interrupt Status

D16

Local Interrupt Output Enable

D17

Local Doorbell Interrupt Enable (Unused)

D18

Local DMA Channel 0 Interrupt Enable

D19

Local DMA Channel 1 Interrupt Enable

D20

Local Doorbell Interrupt Status

D21

DMA Channel 0 Interrupt Status

D22

DMA Channel 1 Interrupt Status

D23 BIST

Interrupt

Status

D24

A ‘0’ indicates a Direct Master was bus master during a Master or Target abort.

D25

A ‘0’ indicates that DMA CH0 was bus master during a Master or Target abort.

D26

A ‘0’ indicates that DMA CH1 was bus master during a Master or Target abort.

D27

A ‘0’ indicates that a Target Abort was generated by the PCI9080 after 256 consecutive Master
retries to a Target.

D31:28 PCI Mailbox 3:0 Write Status

5.3.2.

Serial EEPROM Control, PCI Command Codes, User I/O Control, Init Control Register

(PCI 0x6C, Reset 0x0x001767E)

D3:0

PCI Read Command Code for DMA

D7:4

PCI Write Command Code for DMA

D11:8 PCI Memory Read Command Code for Direct Master (Unused)
D15:12 PCI Memory Write Command Code for Direct Master (Unused)
D16

General Purpose Output (Unused)

D17

General Purpose Input (Unused)

D23:18 Reserved
D24

Serial EEPROM clock for Local or PCI bus reads or writes to Serial EEPROM.

D25

Serial EEPROM chip select

D26

Write bit to serial EEPROM

D27

Read serial EEPROM data bit

D28

Serial EEPROM present

D29

Reload Configuration Registers

D30

PCI Adapter Software Reset

D31

Local Init Status
A ‘1’ indicates Local initialization done.

5.3.3.

PCI Permanent Configuration ID Register

(PCI 0x70, Reset 0x10B59080) )

D15:0 Permanent Vendor ID (0x10B5)
D31:16 Permanent Device ID (0x9080)

5.3.4.

PCI Permanent Revision ID Register

(PCI 0x74) )

D7:0 Permanent

Revision

General Standards Corporation, Phone: (256) 880-8787

Содержание PCI-DIO24PMC-DIO24PCI-DIO24-GD1






























Результаты поиска

Содержание PCI-DIO24PMC-DIO24PCI-DIO24-GD1

Отзывы:

Похожие инструкции для PCI-DIO24PMC-DIO24PCI-DIO24-GD1

Бренды по названию

Популярные бренды

General Standards Corporation PCI-DIO24PMC-DIO24PCI-DIO24-GD1, Руководство пользователя

Результаты поиска

Содержание PCI-DIO24PMC-DIO24PCI-DIO24-GD1

Отзывы:

Похожие инструкции для PCI-DIO24PMC-DIO24PCI-DIO24-GD1

Бренды по названию

Популярные бренды