Generac Power Systems OHVI GSH 190 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 72

background image

4-4

NoTeS

highest rpm under load (see Figure -6). DO NOT EXCEED
RPM

SPECIFICATION.

b. CARBURETOR WITH ADJUSTABLE MAIN JET: Adjust the

carburetor as follows:

() Slowly turn the MAIN JET counterclockwise ( richer)

until rpm or frequency starts to drop off.

(2) Turn the MAIN JET clockwise (leaner) until rpm or

frequency again starts to decrease.

() Turn the MAIN JET counterclockwise (richer) until the

best and most stable frequency or rpm is obtained.

9. Turn off all loads and check the no-load governor setting.

Readjust governor no-load speed, if neces

sary.

Figure 4-6. Adjustable Carburetor

0C1103Arev0.indd 4

6/22/2006 10:50:06 AM

«
...
20
21
22
23
24
...
»

Содержание OHVI GSH 190









































































Отзывы:

Нет отзывов

Похожие инструкции для OHVI GSH 190

Бренд: Vanguard Страницы: 20

EtherCAT BG 65 S

Бренд: Ametek Страницы: 38

Бренд: Hatz Diesel Страницы: 56

Бренд: Motor Power Company Страницы: 59

Бренд: Parker Страницы: 71

Бренд: Superrollo Страницы: 68

Dexxo Pro 1000 RTS

Бренд: SOMFY Страницы: 13

Elixo 500 230 V

Бренд: SOMFY Страницы: 44

Elixo 500 230 V

Бренд: SOMFY Страницы: 48

Бренд: Perkins Страницы: 54

Бренд: Lycoming Страницы: 194

RolloTube Comfort 2360 20 80

Бренд: RADEMACHER Страницы: 8

Бренд: Louvolite Страницы: 2

Бренд: RAAMDECORATIE Страницы: 45

Бренд: Baumuller Страницы: 22

Shire 15 Work Boat YM

Бренд: Barrus Страницы: 44

Бренд: Ingersoll-Rand Страницы: 159

G18 LT20 Series

Бренд: Wood-mizer Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды