background image

5-1

SeCTIoN 5: oPTIoNAl Idle CoNTrol

GeNerAl

Some applications, such as AC generators, may be equipped 

with an automatic idle control system. This type of system pro-
vides greatly improved fuel economy by running the engine at a 
high governed speed only when electrical loads are connected 
to the generator. When the electrical loads are disconnected, 
engine speed will automatically be reduced to an idle.

oPerATING INSTruCTIoNS

BEFORE START UP

*

   CAuTIoN! before cranking and starting the engine, 

always  set  the  idle  control  switch  to  oFF.  Set  the 
switch to its oN position only after the engine has 
stabilized at high governed speed (see Figure 5 .1).

ENGINE RUNNING:

To have the engine run at high governed speed only when 

electrical  loads  are  connected  and  turned  on,  set  the  idle 
control switch to ON. The engine will decelerate to idle speed 
when loads are disconnected or turned off. If you wish to have 
the engine run at high governed speed at all times (with or 
without loads connected), set the idle control switch to OFF.

ON

OFF

Figure 5-1. Idle Control Switch Located on a  

Generator Control Panel

CIrCuIT oPerATIoN

.  With Idle Control switch set to ON:

a. AC  power  is  delivered  from  the  generator’s  AC  power 

windings to a circuit board, for operation of the circuit 
board.

b. With  electrical  loads  connected  to  the  generator,  cur-

rent will flow through the primary windings of a sensing 
transformer. A proportional voltage and current will then 
be induced into the transformer’s secondary windings.

c. Current from the transformer secondary windings is deliv-

ered to the circuit board. Circuit board action then opens 
the circuit to an idle control solenoid.

d. The idle control solenoid de-energizes and engine speed 

is established by the engine governor.

e. When electrical loads are disconnected or turned off, cur-

rent flow through the transformer primary windings will 
terminate. Voltage and current cannot be induced into 
the  transformer  secondary  windings  and  the  solenoid 
energizes.

f. Zero current flow of the transformer secondary windings 

is sensed by the circuit board. The circuit board then closes 
the circuit to the idle control solenoid.

g. The energized solenoid pulls the carburetor throttle arm 

against its idle speed stop screw.

 The engine decelerates 

to idle speed, about 2280-2400 rpm (38-40 Hertz).

2.  Idle control switch set to OFF:

a. AC power is not available to the circuit board. The idle 

control  solenoid  will  then  remain  de-energized  at  all 
times.

b. The engine will run at high governed speed.

A. Schematic

B. Pictorial

44X

44X

44

44

33

11X

11A

110

155

81

82

22

11

22

156

STATOR POWER WINDINGS

CIRCUIT
BOARD

COIL (MAGNET)

TRANSFORMER

SWITCH

TRANSFORMER

CIRCUIT
BOARD

SWITCH

COIL

22

11A

11X 44

155

156

Figure 5-2. Idle Control System (Typical AC Generator)

  5

0C1103Arev0.indd   1

6/22/2006   10:50:07 AM

Содержание OHVI GSH 190









































































Отзывы: