Generac Power Systems OHVI GSH 190 Скачать руководство пользователя страница 45

Страница: 45 / 72

CrANkCASe Cover reMovAl

Before attempting to remove the crankcase cover, remove

all rust, burrs and paint from the power take-off (PTO) end of
the crankshaft. This will reduce the possibility of damaging the
oil seal in the crankcase cover during cover removal. Remove
the crankcase cover as follows:

. Drain oil from the crankcase.

2. Remove the engine cylinder head, push rods and push rod

guide plate (see Section 6).

. Remove all flange head bolts that retain the crankcase

cover.

. Remove the crankcase cover (Figure -). If necessary,

tap lightly with a soft hammer on alternate sides of cover.
Be aware that the oil pump rotors may drop out as the
crankcase cover is removed.

CRANKCASE
COVER

CRANKCASE
COVER BOLT

CRANKCASE
COVER GASKET

CRANKCASE

Figure 11-1. Crankcase Cover Removal

CrANkSHAFT CAMSHAFT ANd bAlANCer reMovAl

With the crankcase cover removed, the crankshaft and cam-

shaft (and balancer on large frame engines) can be removed
from their crankcase bores. Remove these components as
follows (see Figure -2):

. Tip the engine over onto the flywheel end of the

crankshaft.

2. Reach in with two fingers and hold the tappets up and

clear of the camshaft lobes. Then, remove the camshaft,
both tappets, and the inner and outer oil pump rotors.

Note: Some models may be equipped with a camshaft
spring washer.

. Remove the balancer (large frame engine only).

. Before removing the crankshaft, remove the engine fly-

wheel (see Section 2).

5. Turn the crankshaft to access the two (2) connecting rod

bolts.

6. Remove the connecting rod bolts and connecting rod

cap.

7. Push connecting rod and piston up and out of cylinder.

bAlANCer INSPeCTIoN

(lArGe FrAMe eNGINeS, FIGure 11-3)

Clean the balancer in solvent. Then inspect the balancer as

follows:

. Check for physical damage. Replace the balancer if

damaged.

2. Measure the outside diameter (O.D.) of the balance shaft

ends. Replace balancer if wear limits are exceeded.

NOTE: Refer to "ENGINE SPECIFICATIONS", Section 15, in
this manual for design sizes and wear limits.

. Measure the inside diameter (I.D.) of the balancer shaft

bearing bore in the crankcase cover and in the crankcase.

a. If balancer bearing bore in crankcase cover exceeds wear

limits, replace the crankcase cover (see Section 5).

b. If balancer bearing bore in crankcase exceeds wear limits,

replace the crankcase assembly (see Section 5).

BALANCER

CAMSHAFT

OIL PUMP

CRANKSHAFT

Figure 11-2. Crankshaft, Camshaft and Balancer Removal

SeCTIoN 11: CrANkSHAFT & CAMSHAFT

0C1103Arev0.indd 1

6/22/2006 10:51:29 AM

Содержание OHVI GSH 190









































































Результаты поиска

Содержание OHVI GSH 190

Отзывы:

Похожие инструкции для OHVI GSH 190

Бренды по названию

Популярные бренды

Generac Power Systems OHVI GSH 190, Руководство по обслуживанию

Результаты поиска

Содержание OHVI GSH 190

Отзывы:

Похожие инструкции для OHVI GSH 190

Бренды по названию

Популярные бренды