Generac Power Systems OHVI GSH 190 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 72

background image

9-7

SeCTIoN 9: lubrICATIoN SYSTeM

OIL PUMP
INNER ROTOR

OIL PUMP
OUTER ROTOR

CRANKCASE
GASKET

OIL PICKUP
ASSEMBLY

CRANKCASE
COVER BOLTS

Figure 9-14. Reassembly of Crankcase Cover and Oil Pump

Figure 9-15. Location of Oil Pump Drive Pins

2. Carefully install the crankcase cover. Align the cover with

dowel pins on the crankcase flange, as well as with the
crankshaft and camshaft. Make sure the cover gasket is
on. Rotate the crankshaft to align the oil pump inner and
outer rotors. The cover should fall easily into place. DO
NOT FORCE.

. Install the crankcase cover bolts and torque (see Figure

9-6). Refer to Section for torque specifications.

Figure 9-16. Crankcase Cover Bolt Tightening Sequence

. After tightening the crankcase cover bolts, make sure the

crankshaft turns freely.

oPTIoNAl oIl FIlTer

The optional oil filter is a "spin-on" type. An oil filter adapter

is bolted to the oil filter pad. When installing the oil filter,
coat the filter seal with engine oil. Then install the filter and
tighten until its seal contacts the filter adapter. After the filter
seal contacts the adapter, tighten / to turn more. (See
Figure 9-7)

OIL FILTER
ADAPTER

OIL FILTER
ADAPTER
BOLT

OIL FILTER
ADAPTER
GASKET

OIL FILTER

OIL FILTER
PAD

Figure 9-17. Optional Oil Filter

9

0C1103Arev0.indd 7

6/22/2006 10:51:23 AM

«
...
39
40
41
42
43
...
»

Содержание OHVI GSH 190









































































Отзывы:

Нет отзывов

Похожие инструкции для OHVI GSH 190

Бренд: Waldbeck Страницы: 72

Бренд: Tanaka Страницы: 11

Бренд: ZAFFER Страницы: 28

Бренд: JetCat Страницы: 54

Бренд: Volvo Penta Страницы: 84

Бренд: Volvo Penta Страницы: 88

Бренд: Lombardini Страницы: 50

Бренд: Lombardini Страницы: 114

Бренд: Lycoming Страницы: 38

RolloTube Comfort 2360 20 80

Бренд: RADEMACHER Страницы: 8

Бренд: Texas Equipment Страницы: 44

Бренд: KAZZ Страницы: 11

Megatorque Motor EGA

Бренд: NSK Страницы: 10

Бренд: Electro motive Страницы: 287

Бренд: Yanmar Страницы: 33

Car engines GX640

Бренд: Honda Страницы: 33

Бренд: Honda Страницы: 38

Бренд: Honda Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды