GEISMAR MPR-M Скачать руководство пользователя страница 11

Страница: 11 / 132

Chap. 1 — page 1

L.GEISMAR Company

– Prohibited Reproduction©

HYDRAULIC RAIL THREADER

H90461 / NO 10055

TYPE MPR – M

Chapter 1 – Safety

1 – 1 Foreword

Please review the Safety Instructions below applicable to equipment operations.

Three pictograms are used to call users’ attention.

This symbol signals potentially hazardous conditions that might result in
serious or fatal accidents if safety instructions are ignored.

This symbol points out to situations or events that might result in injury if
safety instructions are ignored.

This symbol reminds users of safety rules or of hazardous situations that
might result when such rules are broken.

All persons involved in the operation, maintenance, storage or purchase of this

equipment are required to read and apply these Operation & Maintenance Instructions.

These instructions are intended for all Users in charge of equipment operation and

maintenance.

Instructions and illustrations included in this handbook may differ from actual details

and accessories of your equipment. Basic equipment features may be similar, but the

GEISMAR

Company reserves its right to make improvements to the equipment.

These instructions may refer to various equipment options.

For additional information on your equipment or this handbook, please contact the

GEISMAR

Company.

When ordering spare parts, or requesting information or service, please provide

equipment reference details, including equipment type, code and serial number.

This information can be found on the nameplate. The nameplate shall be kept in

good condition.

Содержание MPR-M





































































































































Результаты поиска

Содержание MPR-M

Отзывы:

Похожие инструкции для MPR-M

Бренды по названию

Популярные бренды

GEISMAR MPR-M, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MPR-M

Отзывы:

Похожие инструкции для MPR-M

Бренды по названию

Популярные бренды