gefran POS-MINI SIEIDrive страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 48

background image

GEFRAN

—————— Instruction manual ——————

32

This function is useful in case of mechanical structures, whose movements are subject to strong frictions.
If the axis does not return to the threshold within the specified time, the control unit generates a Warning and
not a serious alarm condition.

•

Set the

MaxPosTime

parameter with a value lower or equal to the one set in

MaxStatErr

.

•

Set the

MaxPosTime

parameter with the time value, in seconds, allowed to the axis to return to the

threshold stated in the previous point.

5.1.3.18. Automation of the zero cycle procedure

In order to automate, at the start, the zero cycle procedure without having to send the specific command, set
the parameter

Type Cycle0 = 3

.

5.1.3.19. End of the operations

•

Take the control unit to the IDLE status.

•

Save the parameters in Flash.

•

Save the parameters on a file.

5.2. CONFIGURATION EXAMPLE FOR A LINEAR MOVED AXIS WITH AN
INCREMENTAL ENCODER

5.2.1. Axis Features

5.2.1.1. Incremental Encoder

•

Pulses/Revolution = 1024 EI_Pulses/Revolution = 1024 pulses

•

Bit/Revolution

EI_Bit/Revolution = EI_Pulses/Revolution * 4 = 1024 * 4 = 4096 bits

5.2.1.2. Motor

•

Motor max. revolutions

MO_MaxRevolutions = 3000 rpm

•

Motor:Encoder Ratio

MO_Motor:EncoderRatio = 1

•

Bits contained in a motor revolution

MO_Bit1MotorRevolution = 4096 bits

5.2.1.3. Motor Reducer

•

Reduction ratio

MR_Ratio = 9

•

Diameter of the output pinion

MR_PinionDiameter = 10 millimeters

5.2.1.4. Axis

Axis stroke

AX_Stroke = 1200 millimeters

5.2.1.5. Requirements

The axis unit of measure must be stated in millimeters.
The axis maximum speed has to be equal to the maximum speed allowed by the motor.
The axis must reach the maximum speed in: RQ_AccelerationTime = 0.5 seconds.

«
...
30
31
32
33
34
...
»

Содержание POS-MINI SIEIDrive

















































Отзывы:

Нет отзывов

Похожие инструкции для POS-MINI SIEIDrive

Бренд: NBK Страницы: 52

Бренд: Renishaw Страницы: 59

Бренд: ProArc Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды