GEA Geneglace F15 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 46

background image

3

Contractor’s manual

F15 - F30 Generators

Manual For F15 and F30 - Mill.: 2008 - 11 / Mod. : JPM 05

Page

Type / Model

Pression de service Max. (PS)

Max. working

Intensité maxi. / max.

Charge fluide maxi

Max. refrigerant

N° construction / Serial

Puissance installée

Installed

Fluide / Fluid

Tension (V) - Phases

Voltage (V) - Phases

Fréquence / Frequency

GEA Geneglace s.a.s.

9 rue des orfèvres

44840 Les Sorinières - France

+33

(0)2.51.19.10.51

Kg

A

Bar

kVA

Date

Hz

IDENTIFICATION

Introduction

Your GENEGLACE ice machine has been designed and manufactured in accordance with current regulations; built
with the greatest care, it has been subjected to a test for long-lasting quality. Nevertheless, if you discover a manu-
facturing fault and in order to protect your GENEGLACE machine, please do not attempt a repair but contact us as
soon as possible.
Any reproduction of all or part of this notice is subject to prior permission.
The information contained in this notice is subject to modifi cation without prior notice.
In order to update the present notice, please advise us by return of any errors or misunderstandings that may have
slipped in.
GENEGLACE cannot be held responsible for damage or problems in operation occurring with GENEGLACE machines
as a result of use outside the operating or safety limits or even the use of options or consumable items other than
those approved by GENEGLACE.

IDENTIFICATION

Manufacturer Plaque

«
...
3
4
5
6
7
...
»

Содержание Geneglace F15















































Отзывы:

Нет отзывов

Похожие инструкции для Geneglace F15

Бренд: Axxion Страницы: 3

Бренд: Jam Страницы: 2

Бренд: Daewoo Страницы: 49

Бренд: Powermate Страницы: 12

ProTravel PT-50

Бренд: Sangean Страницы: 56

Бренд: Pulsar Страницы: 39

Бренд: Wacker Neuson Страницы: 46

Бренд: Sangean Страницы: 26

Бренд: Kohler Страницы: 84

Бренд: Far Tools Страницы: 54

Бренд: Roberts Страницы: 8

Бренд: Tektronix Страницы: 6

Бренд: Tektronix Страницы: 12

Tiptop Audio Eurorack 200 Series

Бренд: Buchla Страницы: 2

Бренд: Excera Страницы: 9

Бренд: Nature's Generator Страницы: 19

Бренд: Casals Страницы: 11

Бренд: JVC Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды