GEA Geneglace F15 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 46

background image

10

Contractor’s manual

F15 - F30 Generators

Manual For F15 and F30 - Mill.: 2008 - 11 / Mod.: JPM 05

Page

10 cm mini

1
2
3
4
5

6.1 Positioning the machine

- Place the generator on a level, fl at surface.

- The generator must be located in a position protected

from bad weather, water spray or any other liquid

and in a non-aggressive environment.

- Position the generator so as to maintain adequate ac-

cess for upkeep and maintenance (see Installation

Handling - free access)

- The generator must be mounted suffi ciently high, in order

to permit suitable storage for its daily production of ice

(e.g. cold chamber, static or orbital silo, etc.).

- Avoid locating the ice output in the air fl ow from an

evaporator.

- Do not reduce the cross section of the ice output.

Note

In order to facilitate all upkeep and maintenance
work on the generator, (such as regular greasing of
the bearings of the shaft and the reamer), provide

accessibility below and above the machine.

Fig 512.

Optional chute, easily removable for mainte

-nance of generator.

Important

Risks of freezing during machine downtime

:

protect the base of the pump and valve fl oat by

means of a heater housed in the base.

This device will only be effective for an air tem-
perature of - 10°C to + 5°Cmaximum for a period
of 12 to 24 h. Beyond that, it is preferable to drain
the machine if it is stopped. Also protect the water

supply pipework

Note

When fi tting a heater resistance, provide a
circuit breaker for protection and a thermostat

to monitor the ambient air temperature.

6.2 Mountings

The opening in the generator mounting must be at least
equal to the diameter «G» of the ice chute.

Important

Do not forget to add a silicone seal all round the

base of the generator to prevent water entering the

ice storage area.

The unit is mounted by the bottom of the base using the
two holes provided for the purpose. Fibre seals ensure
the mountings are watertight.

Positioning the machine

Ice

overfl ow

area

Access to

emergency

switch

Maxi 45°

Chute

PVC

1 Cap
2 Lag

screw

3 Fibre

seal

4 Pin
5 Silicone

seal

Mounting

In concrete

In woodf

«
...
10
11
12
13
14
...
»

Содержание Geneglace F15















































Отзывы:

Нет отзывов

Похожие инструкции для Geneglace F15

Бренд: CA Страницы: 6

Бренд: Sangean Страницы: 22

Бренд: A2Z Ozone Страницы: 14

Бренд: unicraft Страницы: 66

Бренд: LONCIN Страницы: 27

PS906800 Series

Бренд: Power Stroke Страницы: 72

Бренд: FEESER Страницы: 32

MPI-II LBI-38558B

Бренд: Ericsson Страницы: 14

Бренд: ISOUND Страницы: 3

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 44

580.327182 Operators

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды