GE PACSystems* RX3i Скачать руководство пользователя страница 93

Страница: 93 / 116

GFK-2572

3-1

Modify-Level Commands

This chapter describes commands that are available for Modify-level access to the Command

Line Interface. Global commands, which are common to both Monitor- and Modify-level access,

are defined in chapter 1.

Modify Access Level Commands



Arp



Blinkld



Clear arp



Clear counters



Clear counters profinet



Clear log



Clear statLED



Default



LoginCfg



Logout



Monport



Ping



Restart



SessionTimeout



Telnetd



Time

Modify-Level Login

Logging into and out of Modify-level access is done using the

login

and

logout

commands. Both

the login name and password are case-sensitive (however, commands are not case-sensitive).

When Modify-level access is enabled, the command line prompt displays “=” following the

device name.
Login name (cannot be changed):

admin

Default password:

system

The password can be changed from the Modify level.

Chapter

Содержание PACSystems* RX3i





















































































































Результаты поиска

Содержание PACSystems* RX3i

Отзывы:

Похожие инструкции для PACSystems* RX3i

Бренды по названию

Популярные бренды

GE PACSystems* RX3i, Руководство по интерфейсу командной строки

Результаты поиска

Содержание PACSystems* RX3i

Отзывы:

Похожие инструкции для PACSystems* RX3i

Бренды по названию

Популярные бренды