GE PACSystems* RX3i Скачать руководство пользователя страница 67

Страница: 67 / 116

show port

GFK-2572

Chapter 2 Monitor Level Commands

2-51

Displaying Help for the Show Port SFP Command

The

show port sfp help

command provides definitions for the fields displayed in the

show port

sfp

command output.

Screen Display

device-name

> show port sfp help

[Additional output not shown here. See the following table for definitions.]

Definitions for show port sfp Command Output

e I

D Fiel

Heading

Description

Identifier - Type of serial transceiver.

Ext. Identifier - Extended identifier of type of serial Transceiver.

Connector - Code for connector type.

Transceiver

Transceiver - Code for electronic compatibility or optical Compatibility.

Encoding - Code for serial encoding algorithm.

Nominal bit rate, units of 100 MBits/sec.

Not Available/Reserved. Set to 0.

Length(9mm)/km - Link length supported for 9/125 mm fiber, units of km.

Length (9mm) - Link length supported for 9/125 mm fiber, units of 100 m.

Length (50mm) - Link length supported for 50/125 mm fiber, units of 10 m.

Length (62.5mm) - Link length supported for 62.5/125 mm fiber, units of 10 m.

Length (Copper) - Link length supported for copper, units of meters

VendorName

Vendor name - SFP transceiver vendor name (ASCII).

VendrOUI

Vendor OUI - SFP transceiver vendor IEEE company ID.

VendorPartNumber

Part number provided by SFP transceiver vendor (ASCII).

VendorRev

Revision level for part number provided by vendor (ASCII).

WvLen

Wavelength - Laser wavelength.

CC_BASE - Check code for Base ID Fields (addresses 0 to 62). A “|” symbol is placed

next to “CB” to indicate the end of the Base ID Fields.

Extend

ed I

Fiel

Heading

Description

Optns

Options - Indicates which optional transceiver signals are implemented.

Maximum bit rate - Upper bit rate margin, units of %.

Minimum bit rate - Lower bit rate margin, units of %.

VndrSerNo

Vendor Serial No. - Serial number provided by vendor (ASCII).

DateCode

Date code Vendor’s manufacturing date code.

Diagnostic Monitoring Type - Indicates which type of diagnostic monitoring is

implemented (if any) in the transceiver.

Enhanced Options - Indicates which optional enhanced features are implemented (if

any) in the transceiver.

Indicates which revision of SFF-8472 the transceiver complies with.

CC_EXT - Check code for the Extended ID Fields (addresses 64 to 94). A “|” symbol

is placed next to “CE” to indicate the end of the Extended ID Fields.

VendorSpecific

Vendor Specific - Vendor Specific EEPROM data.

Reserved

Reserved - Reserved for SFF-8079.

Содержание PACSystems* RX3i





















































































































Результаты поиска

Содержание PACSystems* RX3i

Отзывы:

Похожие инструкции для PACSystems* RX3i

Бренды по названию

Популярные бренды

GE PACSystems* RX3i, Руководство по интерфейсу командной строки

Результаты поиска

Содержание PACSystems* RX3i

Отзывы:

Похожие инструкции для PACSystems* RX3i

Бренды по названию

Популярные бренды