background image

show ip 

 

GFK-2572 

Chapter 2  Monitor Level Commands 

2-33 

2

 

  

 

 

IP Counters 

The following table defines each of the IP Counters. 

Counter Name 

Counter Description 

InRecv  

The total number of input datagrams received from interfaces, including those 

received in error. 

InHdrErr  

The number of input datagrams discarded due to errors in their IP headers. 

InAdrErr  

The number of input datagrams discarded because the IP address in their IP 

header’s destination field was not a valid address to be received at this entity.

 

ForwDgms  

The number of input datagrams for which this entity was not their final IP 

destination, as a result of which an attempt was made to find a route to forward 

them to that final destination. (Not used in this release.) 

InUnkPro  

The number of locally–addressed datagrams received successfully but 

discarded because of an unknown or unsupported protocol. 

InDiscds  

The number of input IP datagrams for which no problems were encountered to 

prevent their continued processing, but which were discarded (for example, for 

lack of buffer space). 

InDelivs  

The total number of input datagrams successfully delivered to IP user–protocols 

(including ICMP). 

OutReq  

The total number of IP datagrams which local IP user–protocols (including 

ICMP) supplied to IP in requests for transmission. 

OutDiscd  

The number of output IP datagrams for which no problem was encountered to 

prevent their transmission to their destination, but which were discarded (for 

example, for lack of buffer space). 

OutNoRts  

The number of IP datagrams discarded because no route could be found to 

transmit them to their destination. 

ReasmTO  

The maximum number of seconds during which received fragments are held 

while they are awaiting reassembly at this entity. (Not used in this release.) 

ReasmReq  

The number of IP fragments received which needed to be reassembled at this 

entity. 

ReasmOKs  

The number of IP datagrams successfully re–assembled. 

ReasmFai  

The number of failures detected by the IP re–assembly algorithm (for example, 

timed out, errors, message size too big….) 

FragOKs  

The number of IP datagrams that have been successfully fragmented at this 

entity. 

FragFail  

The number of IP datagrams that have been discarded because they needed to 

be fragmented at this entity but could not be, e.g., because their Don’t Fragment 

flag was set. 

FragCrea  

The number of IP datagrams that have been generated as a result of 

fragmentation at this entity. 

Filtered  

IP packets ignored because not addressed to this node and destination is 

unreachable. 

Содержание PACSystems* RX3i





















































































































Отзывы: