GE PACSystems* RX3i Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 116

background image

`

show tcp

GFK-2572

Chapter 2 Monitor Level Commands

2-71

2

Displaying Status Details of TCP Connections

Screen Display

device-name> show tcp details
01-JAN-2000 05:44:17.0000
<<< TCP Status Details >>>
Tcp:
  0 active connection openings
  2 passive connection openings
  0 failed connection attempts
  1 connection resets received
  1 connections established
  43 segmemts received
  36 segments sent out
  11 segments retransmitted
  0 bad segments received
  2 resets sent
device-name>

TCP Counter Definitions

Counter

Description

ActOpens

The number of times TCP connections have made a direct transition to the SYN–

SENT state from the CLOSED state.

PasOpens

The number of times TCP connections have made a direct transition to the SYN–

RCVD state from the LISTEN state.

AtmptFai

The number of times TCP connections have made a direct transition to the

CLOSED state from either the SYN–SENT state or the SYN–RCVD state, plus

the number of times TCP connections have made a direct transition to the

LISTEN state from the SYN–RCVD state.

EstabRes

The number of times TCP connections have made a direct transition to the

CLOSED state from either the ESTABLISHED state or the CLOSE–WAIT state.

CurEstab

The number of internal TCP data structures currently in use. This value

corresponds to the “Current Conn” value in the status section.

InSegs

The total number of segments received, including those received in error. This

count includes segments received on currently established connections.

OutSegs

The total number of segments sent, including those on current connections but

excluding those containing only retransmitted bytes.

RtranSeg

The total number of segments retransmitted – that is, the number of TCP

segments transmitted containing one or more previously transmitted bytes.

InErrs

TCP segments received in error.

SndRsts

TCP segments sent with RST flag.

«
...
85
86
87
88
89
...
»

Содержание PACSystems* RX3i





















































































































Отзывы:

Нет отзывов

Похожие инструкции для PACSystems* RX3i

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Barcelona Страницы: 8

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

Бренд: hager Страницы: 2

Бренд: hager Страницы: 4

Бренд: Jetter Страницы: 24

Бренд: Challenger Lifts Страницы: 20

Бренд: Daruifuno Страницы: 24

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды