GE JSP62GN, Инструкция по использованию и уходу

Страница: 32 / 48

Care Cleaning
(continued)
Solid Disk Element Module
Solid disk elements are easy to
clean because the element is raised
above the module and sealed to it.
Food spills can not flow under the
cookware or the element. Spills
stay on the module surface where
they cool and are easy to wipe up.
Be sure the controls are off and
the module and elements are cool
before handling or cleaning. The
elements cool slowly and do not
glow red as open coil elements do
when they are hot.
The trim rings around the elements
are stainless steel and may be
cleaned with a stainless steel cleaner.
When cleaning solid elements:
●
Rub in the direction of the
circular ridges.
●
Rinse completely and wipe dry.
Turn elements on to dry
completely and prevent rust.
the elements have been
cleaned, heated to dry and cooled,
you may wish to use a paper towel
to apply a small amount of non-
stick, salt-free cooking oil. Use a
clean paper towel to remove any
excess oil. Expect a little smoking
the next time the elements are
turned on.
Solid Disk Care
The solid elements can be cleaned
with scouring powder or a scouring
pad the same way as cleaning a
iron skillet.
If the elements have been scoured
or if they appear dull, oil them
when cool with anon-stick,
free cooking oil. Oiling the
elements from time to time will
maintain their good appearance
and help protect them from rust.
It is normal for cast iron to lose its
luster as it ages. This will not affect
performance or durability of the
element.
You can also buy products (such as
EGO
or Rutland )
to restore appearance of the solid
elements. Follow the manufacturers’
instructions on the packages.
The red dot in the center of
each element can be removed by
scouring. The dot is for factory
identification only and removing it
will not affect performance or
durability of the element.
Because the elements are cast iron,
they should be kept dry to prevent
rust. Be sure the bottom of your
pan is dry before you put it on the
element. After cleaning the
elements, turn them on a few
minutes to completely dry them.
Radiant Module
With proper care and cleaning,
the radiant module will give you
efficient and satisfactory service.
Remove soiling mineral deposits
from evaporated water spills or
metal rub-off from aluminum
cookware. Otherwise, it will bum
on the surface and cause permanent
discoloration. Follow directions
below carefully in caring for your
module to assure safe and proper
maintenance.
Be sure that controls are turned
off and the module is cool before
cleaning.
Radiant Module Glass Top
Wipe glass clean after each use.
Use a glass cleaner and paper
towels. All-purpose non-abrasive
cleansers, such as
or
special maintop cleaning creams,
such as Cook Top brand, can also
be used. Remove stubborn soils
with a paste of baking soda and
water. A plastic or nylon mesh
scouring pad can be used.
Do not use a dishcloth or sponge to
wipe the maintop. They may leave a
film of detergent which can
discolor the maintop when heated.
We recommend that you use paper
towels or a clean cloth which is
used only for maintop cleaning.
For burned-on spillover:
●
Remove excess soil with
edged razor blade scraper. Hold the
blade at about a 30° angle to the
surface
and scrape off the –
Scrub the glass top with an
purpose non-abrasive cleanser or
with a maintop cleaning
Rinse well and wipe dry.
●
Never use abrasive scouring pads
or powders on the glass top. Plastic
mesh pads such as
maybe
used.
Stainless Steel Frame
The frame around the glass is
stainless steel. It can be cleaned
using the same methods for
cleaning the glass top. Do not
scrape the metal frame with any
sharp objects or use abrasives as
this will mar the finish.
32