GE IC3645SP4U450N10 Скачать руководство пользователя страница 8

Страница: 8 / 69

BASIC OPERATION AND FEATURES

SX TRANSISTOR CONTROL

Page

Section 2.3.3 Hourmeter Readings

Section 2.2.5 Low Voltage

This feature will display the recorded hours of use of the

traction and pump control to the Dash Display each time

the key switch is turned off.

Batteries under load, particularly if undersized or more

than 80 percent discharged, will produce low voltages at

the control terminals. The SX control is designed for use

down to 50 percent of a nominal battery voltage of 36-84

volts, and 75 percent of a nominal battery voltage of 24

volts. Lower battery voltage may cause the control to

operate improperly, however, the resulting PMT should

open the Line contactor, in the event of a failure.

Section 2.3.3.a Maintenance Alert & Speed Limit

This feature is used to display Status Code 99 and/or

activate a speed limit when the vehicle operating hours

match the hours set into the maintenance alert register.

This feature is set with the Handset using Functions 19 and

20. The operator is alerted that maintenance on the vehicle

is required.

Section 2.3 Diagnostics

Section 2.3.1 Systems Diagnostics

Section 2.3.4 Battery Discharge Indication (BDI)

The control detects the system's present operating status

and can be displayed to either the Dash Display or the

Handset. There are currently over 70 status codes that are

available with SX systems using Traction and Pump

controls and Truck Management Module (TMM). Along

with the status code display from the TMM, the SX control

is capable of reducing the current to the motor, alerting the

operator of a critical fault condition.

The latest in microprocessor technology is used to provide

accurate battery state of charge information and to supply

passive and active warning signals to the vehicle operator.

Features and functions:

Displays 100 to 0 percent charge.

Display blinks with 20% charge. Disables pump circuit

with 10% charge. Auto ranging for 36/48 volt operation.

Adjustable for use on 24 to 80 volts.

Section 2.3.2 Status Codes

Section 2.3.2a Standard Status Codes

Section 2.3.4.a Internal Resistance Compensation

The SX traction control has over 30 Status Codes that

assist the service technician and operator in trouble

shooting the vehicle. If mis-operation of the vehicle occurs,

a status code will be displayed on the Dash Display for

vehicles so equipped, or be available by plugging the

Handset into the “y” plug of the logic card.

This feature is used when the Battery Discharge Indicator

is present. Adjustment of this function will improve the

accuracy of the BDI.

Section 2.3.5 Handset

With the status code number, follow the procedures

outlined in DIAGNOSTIC STATUS CODES to determine the

problem and a solution.

This is a multi-functional tool used with the LX, ZX, and SX

Series GE solid state controls. The Handset consists of a

Light Emitting Diode (LED) display and a keyboard for data

entry. Note, for ordering purposes, a separate Handset part

is required for SX controls.

Note: The Status Code Instruction Sheets do not claim to

cover all possible causes of a display of a "status code ".

They do provide instructions for checking the most direct

inputs that can cause status codes to appear.

Features and functions:

Monitor existing system status codes for both traction

and pump controls. Monitor intermittent random status

codes.

Section 2.3.2.b Stored Status Codes

Monitor battery state of charge, if available.

This feature records the last 16 "Stored Status Codes" that

have caused a PMT controller shut down and/or disrupted

normal vehicle operation. (PMT type faults are reset by

cycling the key switch). These status codes, along with the

corresponding BDI and hourmeter readings, can be

accessed with the Handset, or by using the RS 232

communications port and dumping the information to a

Personal Computer terminal.

Monitor hourmeter reading on traction and pump

controls. Monitor or adjust the control functions.

Section 2.3.6 RS 232 Communication Port

This serial communication port can be used with

Interactive Custom Dash Displays to allow changes to

vehicle operating parameters by the operator. Or, it can be

used by service personnel to dump control operating

information and settings into a personal computer program.

October 2002

Содержание IC3645SP4U450N10






































































Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды

GE IC3645SP4U450N10, Инструкция по установке и эксплуатации

Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды