GE IC3645SP4U450N10 Скачать руководство пользователя страница 9

Страница: 9 / 69

BASIC OPERATION AND FEATURES

SX TRANSISTOR CONTROL

Page

Section 2.3.6.a Interactive Dash Display
Modes

The Interactive Custom Dash Display allows the operator to

select the best vehicle performance for changing factory

(task) conditions. There are four (4) "operator interaction

modes" that can be selected by depressing a push button

on the dash display.

From the Dash Display, the operator may select any of four

pre-set interactive modes consisting of (4) Controlled

Acceleration levels, (4) Field Weakening levels and (4)

Speed Limits.

These interactive modes are "pre-set" using the Handset

(Functions 48-62) or a personal computer (Functions 97-

112). This feature allows the operator to select the best

vehicle performance for changing factory (task) conditions.

Section 2.3.7 Circuit Board Coil Driver Modules

Coil drivers are internal to the control card, and are the

power devices that operate the Line and SP contactor

coils. On command from the control card, these drivers

initiate opening and closing the contactor coils. All driver

modules are equipped with reverse battery protection, such

that, if the battery is connected incorrectly, the contactors

can not be closed electrically.

Section 2.3.8 Truck Management Module (TMM)

The Truck Management Module is a multifunction

accessory card, or an integral function of the GE Pump

controls when used with the SX Traction control. The

Module provides the OEM the ability to initiate status codes

or operator warning codes to be displayed on the Dash

Display, whenever a normally open switch or sensor wire

provides a signal to the Module.

The TMM Module can be used to display a separate status

code indicating over-temperature of traction motors,

hydraulic motors, or any other device or system that can

activate a switch that closes.

The TMM Module can also be used as a Brush Wear

Indicator (BWI). The Brush Wear Indicator is designed to

detect a "worn out brush" and display a fault code on the

Dash Display to warn maintenance personnel that the

motor brushes need to be replaced before they wear to the

point of causing destructive damage to the motor

commutator surface.

Section 2.4 Hydraulic Pump Control

This hydraulic motor controller consists of the following

features:

Three speeds, adjustable from O to 100% motor

volts. Fixed speeds actuated by switch closure to

negative.

Current limit and controlled acceleration adjustable.

Battery Discharge Indicator interrupt compatible.

Operation of voltage regulator card: This card provides the

basic functions required for controlling the pump control,

optional contactors, and PMT functions. Battery positive is

applied through a main control fuse to the key switch,

energizing the control card power supply input to P1.

When a pump contactor is used, PMT operation is the

same as outlined for the traction controllers.

The three speed (motor volts) reference points P12, P19,

and P20 are selected by connecting these points

independently to battery negative.

The first speed is obtained by closing Speed Limit I (P12) to

control negative. SLl is adjustable by Function 11 using the

Handset to adjust motor voltage from O to 100%. The

specified motor volts will be regulated, however, the

magnitude of motor current will vary depending on the

loading of the vehicle.

The second speed is obtained by closing SL2 (P19) to

control negative. SL2 is adjusted using the Handset and

Function 12 similar to SL1.

The third speed is obtained by closing SL3 (P20) to control

negative. SL3 is adjusted using the Handset and Function

13 similar to SL1.

If more than one Speed Limit is activated, the selected

speed with the highest motor volts will override the low

motor volt speed. The current limit circuit is adjustable and

operates the same as the traction current limit.

The controlled acceleration circuit is adjustable and

operates the same as the traction circuit. Adjustment range

is from 0.1 to 5.5 seconds.

The Battery Discharge Indicator (BDI) interrupt will disable

the hydraulic controller if the connection at P10 loses the

12 volt signal from the traction control. BDI interrupt can be

disabled by Function 17 using the Handset. Select card type

with or without BDI function.

October 2002

Содержание IC3645SP4U450N10






































































Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды

GE IC3645SP4U450N10, Инструкция по установке и эксплуатации

Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды