GE IC3645SP4U450N10 Скачать руководство пользователя страница 7

Страница: 7 / 69

BASIC OPERATION AND FEATURES

SX TRANSISTOR CONTROL

Page

to optimize motor and control performance, and this setting

will be determined by GE and OEM engineers at the time of

vehicle development. This setting must not be changed by

field personnel, without the permission of the OEM.

Section 2.2 System Protective Override

Section 2.2.1 Static Return to Off (SRO)

This inherent feature of the control is designed to require

the driver to return the directional lever to the neutral

position anytime he leaves the vehicle and returns.

Additionally, if the seat switch or key switch is opened, the

control shuts off and cannot be restarted until the

directional lever is returned to neutral. A time delay of

approximately 2 seconds is built into the seat switch input

to allow momentary opening of the seat switch, if a bump is

encountered.

Section 2.1.4.b Speed Limits

This feature provides a means to control speed by limiting

motor volts utilizing three "adjustable speed limits. This

motor volt limit regulates top speed of the transistor

controller, but actual truck speed will vary at any set point

depending on the loading of the vehicle. Each speed limit

can be adjustable with the Handset using Functions 11, 12,

and 13.

Section 2.2.2 Accelerator Volts Hold Off

Section 2.1.5 Ramp Operation

This feature checks the voltage level at the accelerator

input whenever the key switch or seat switch is activated.

If, at start up, the voltage is less than 3.0 volts, the control

will not operate. This feature assures that the control is

calling for low speed operation at start up.

Section 2.1.5a Ramp Start

This feature provides maximum control torque to restart a

vehicle on an incline. The memory for this function is the

directional switch. When stopping on an incline, the

directional switch must be left in its original or neutral

position to allow the control to initiate full power when

restarted. The accelerator potentiometer input will

modulate ramp start current.

Section 2.2.3 Pulse Monitor Trip (PMT)

The PMT design contains three features which shut down,

or lock out, control operation if a fault conditions occurs

that would cause a disruption of normal vehicle operation:

Section 2.1.5b Anti-Rollback

Look ahead

This feature provides retarding torque to limit rollback

speed in the non-travel direction when the ACC pedal is

Look again

Automatic look again and reset

released when stopping on a grade, or when the brake

pedal is released when starting on a grade. This feature

forces the vehicle to roll very slowly down the grade when

accelerator or brake is released. Because the vehicle can

gain significant speed during roll-back, the torque needed

to re-start on the ramp is lower than an unrestricted roll-

back speed.

The PMT circuit will not allow the control to start under the

following conditions:

The control monitors both armature and field FET's at

start-up and during running.

The control will not allow the line contactor to close at

start-up, or will drop it out during running, if either the

armature or field FET's are defective, so as to cause

uncontrolled truck movement.

Section 2.1.6 Steer Pump Contactor Time Delay

This feature provides two options for SP time delay. Option

1 provides a 0.5 to 63 second time delayed drop out of the

steer pump contactor when the Forward or Reverse

directional switch is opened. This Option 1 is overridden by

a 1.5 second time delayed drop out whenever the seat

switch is opened. Option 2 provides a 0.5 to 63 second time

delayed drop out of the SP contactor when the seat switch

is opened.

Section 2.2.4 Thermal Protector (TP)

This temperature sensitive device is internal to the power

transistor (Q1) module. If the transistor's temperature

begins to exceed the design limits, the thermal protector

will lower the maximum current limit, and maintain the

transistors within their temperature limits. Even at a

reduced current limit, the vehicle will normally be able to

reach sufficient speed. As the control cools, the thermal

protector will automatically reset, returning the control to

full power.

Section 2.1.7 On-Board Coil Drivers & Internal Coil
Suppression

Coil drivers for the LINE and SP contactors

are on-board the control card. These contactors must have

coils rated for the vehicle battery volts.

October 2002

Содержание IC3645SP4U450N10






































































Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды

GE IC3645SP4U450N10, Инструкция по установке и эксплуатации

Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды