GE IC3645SP4U450N10 Скачать руководство пользователя страница 1

Страница: 1 / 69

INSTALLATION AND OPERATION

SX TRANSISTOR CONTROL

Page

SEPARATELY EXCITED (SX) TRANSISTORIZED TRACTION MOTOR CONTROL

AND SERIES PUMP MOTOR CONTROL

INSTALLATION AND OPERATION MANUAL

(IC3645SR4W606N6, IC3645SR7W455N8, IC3645SP4U450N10 and IC3645SP7U350N9)

Note: The information contained herein is intended to assist OEM's, Dealers and Users of electric vehicles

in the application, installation and service of GE solid-state controllers. This manual does not purport to

cover all variations in OEM vehicle types. Nor does it provide for every possible contingency to be met

involving vehicle installation, operation or maintenance. For additional information and/or problem

resolution, please refer the matter to the OEM vehicle manufacturer through his normal field service

channels. Do not contact GE directly for this assistance.

Table of Contents

General Electric Company October 2002

Section 1.0

INTRODUCTION.........................................................................................................................................................4

1.1

Motor

Characteristics...............................................................................................................4

1.2

Solid-State

Reversing................................................................................................................5

1.3

Flexible System Application .....................................................................................................5

1.4

More Features with Fewer Components.................................................................................5

Section 2.0

FEATURES OF SX FAMILY OF MOTOR CONTROLLERS.....................................................................................6

2.1

Performance ..............................................................................................................................6

2.1.1 Oscillator

Card

Features...................................................................................................6

2.1.1.a

Standard

Operation...................................................................................................6

2.1.1.b

Creep

Speed ...............................................................................................................6

2.1.1.c

Controlled Acceleration and 1A Time .....................................................................6

2.1.2 Current

Limit.......................................................................................................................6

2.1.3 Braking................................................................................................................................6

2.1.3.a

Plug

Braking...............................................................................................................6

2.1.3.b

Regenerative Braking to Zero Speed.......................................................................6

2.1.3.c

Pedal

Position

Plug

Braking.....................................................................................6

2.1.3.d

Auto

Braking ..............................................................................................................6

2.1.3.e

Brake

Pedal

Regenerative

Braking..........................................................................6

October 2002

Содержание IC3645SP4U450N10






































































Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды

GE IC3645SP4U450N10, Инструкция по установке и эксплуатации

Результаты поиска

Содержание IC3645SP4U450N10

Отзывы:

Похожие инструкции для IC3645SP4U450N10

Бренды по названию

Популярные бренды