Installation Instructions
4
EXHAUST CONNECTION
There are multiple installation options.
Select the most appropriate method for
your installation situation.
WARNING -
TO REDUCE THE RISK
OF FIRE OR PERSONAL INJURY:
• This clothes dryer must be exhausted to the outdoors.
• Use only 4” rigid metal ducting for the home exhaust duct.
8VHRQO\µULJLGPHWDORU8/OLVWHGÀH[LEOHPHWDOVHPL
ULJLGRUIRLOW\SHGXFWWRFRQQHFWWKHGU\HUWRWKHKRPH
exhaust duct. It must be installed in accordance with
the instructions found in “Connecting the Dryer to House
9HQWµRQSDJHVRIWKLVPDQXDO
• Do not terminate exhaust in a chimney, a wall, a ceiling,
JDVYHQWFUDZOVSDFHDWWLFXQGHUDQHQFORVHGÀRRURULQ
any other concealed space of a building. The accumulated
OLQWFRXOGFUHDWHDSRWHQWLDO¿UHKD]DUG
• Never terminate the exhaust into a common duct with a
kitchen exhaust system. A combination of grease and lint
FUHDWHVDSRWHQWLDO¿UHKD]DUG
'R QRW XVH GXFW ORQJHU WKDQ VSHFL¿HG LQ WKH H[KDXVW
length table. Longer ducts can accumulate lint, creating
DSRWHQWLDO¿UHKD]DUG
• Never install a screen in or over the exhaust duct. This will
FDXVHOLQWWRDFFXPXODWHFUHDWLQJDSRWHQWLDO¿UHKD]DUG
• Do not assemble ductwork with any fasteners that
extend into the duct. These fasteners can accumulate
OLQWFUHDWLQJDSRWHQWLDO¿UHKD]DUG
• Do not obstruct incoming or exhausted air.
• Provide an access for inspection and cleaning of the
exhaust system, especially at turns and joints. Exhaust
system shall be inspected and cleaned at least once a
year
.
CONNECTING THE DRYER TO HOUSE VENT
RIGID METAL TRANSITION DUCT
)RU EHVW GU\LQJ SHUIRUPDQFH D ULJLG PHWDO WUDQVLWLRQ
duct is recommended.
• Rigid metal transition ducts reduce the risk of crushing
and kinking.
UL-LISTED FLEXIBLE METAL (SEMI-RIGID) TRANSITION DUCT
,IULJLGPHWDOGXFWFDQQRWEHXVHGWKHQ8/OLVWHGÀH[LEOH
PHWDOVHPLULJLGGXFWLQJFDQEHXVHG.LW:;;
1HYHULQVWDOOÀH[LEOHPHWDOGXFWLQZDOOVFHLOLQJVÀRRUVRU
other enclosed spaces.
7RWDOOHQJWKRIÀH[LEOHPHWDOGXFWVKRXOGQRWH[FHHG
IHHWP
DUCT TAPE OR
DUCT CLAMP
DUCT TAPE OR
DUCT CLAMP
4" METAL DUCT CUT
TO PROPER LENGTH
EXTERNAL DUCT
OPENING
For straight line installation, connect
the dryer exhaust to the external
exhaust hood using duct tape or
clamp.
N
OTE:
W
E STRO
N
GLY RECOMME
N
D SOLID
METAL EXHAUST DUCTI
N
G. HO
W
EVER, IF
FLEXIBLE DUCTI
N
G IS USED IT MUST BE
UL-LISTED METAL,
N
OT PLASTIC.
STANDARD REAR EXHAUST
9HQWHGDWÀRRUOHYHO
STANDARD REAR EXHAUST
9HQWHGDERYHÀRRUOHYHO
NOTE: ELBOWS WILL PREVENT DUCT
KINKING AND COLLAPSING.
ELBOW HIGHLY
RECOMMENDED
ELBOW HIGHLY
RECOMMENDED
RECOMMENDED
CONFIGURATION
TO MINIMIZE
EXHAUST
BLOCKAGE.
EXHAUST SYSTEM CHECK LIST (cont.)
SEPARATION OF TURNS
)RU EHVW SHUIRUPDQFH VHSDUDWH DOO WXUQV E\ DW OHDVW IW RI
straight duct, including distance between last turn and exhaust
hood.
TURNS OTHER THAN 90º
2QHWXUQRIRUOHVVPD\EHLJQRUHG
7ZRWXUQVVKRXOGEHWUHDWHGDVRQHWXUQ
(DFKWXUQRYHUVKRXOGEHWUHDWHGDVRQHWXUQ
SEALING OF JOINTS
• All joints should be tight to avoid leaks. The male end of each
section of duct must point away from the dryer.
• The duct shall not be assembled with screws or other
fastening means that extend into the duct and catch lint.
'XFWMRLQWVFDQEHPDGHDLUDQGPRLVWXUHWLJKWE\ZUDSSLQJ
the overlapped joints with duct tape.
+RUL]RQWDOUXQVVKRXOGVORSHGRZQWRZDUGWKHRXWGRRUV
inch per foot.
INSULATION
Duct work that runs through an unheated area or is near air
conditioning should be insulated to reduce condensation and
OLQWEXLOGXS
