manualshive.com logo in svg

GE Bently Nevada 7200 Series, Руководство по установке

Поделиться
Скачать
GE Bently Nevada 7200 Series Скачать руководство пользователя страница 19

14 mm Proximity Transducer System 7200 Series Installation Manual 

14 

3.3 RECALIBRATION 

Perform the following procedure to recalibrate the transducer. 

 

a.  Remove the protective assembly from the calibration resistor on the Proximitor (use a 

screwdriver to pry away the outer barrier).  Desolder and remove the calibration resistor (see 
Figure 3-1). 

b.  Attach the variable resistor between the calibration resistor terminals. 

c.  Perform the calibration check (Page 3-1) and adjust the variable resistor as appropriate until the 

desired calibration curve is obtained. 

 

NOTE 

Increasing the resistance between the calibration terminals will 
decrease the Proximitor output voltage and slope of the calibration 
curve; decreasing the resistance will cause the Proximitor output 
voltage and slope of the calibration curve to increase. 

 

d.  When the desired average scale factor is obtained, remove the variable resistor from the 

calibration terminals and use the digital multimeter to measure its resistance.  Select a 1% 
tolerance resistor (or two in parallel) equal to the measured resistance of the variable resistor. 

e.   Solder the resistor(s) between the calibration terminals. 

 

CAUTION

 

To prevent damage to components, do not leave the soldering iron in 
contact with the Proximitor terminals too long. 

 

f. 

Remove the room-temperature vulcanizing compound from the epoxy fiberglass shroud. 

g.  Install the shroud over the calibration resistor(s) and encapsulate with room-temperature 

vulcanizing compound that does not have an acid base. 

 

3.4 TROUBLESHOOTING 

The troubleshooting procedure in Table 3-2 helps the user interpret and isolate faults in an installed 
transducer system.  Before beginning the procedure, ensure the system has been installed correctly 
and all connectors have been secured properly in the correct locations. 

 

When a malfunction occurs, locate the fault indication in the left-hand column of Table 3-2.  Then, 
refer to the center column which lists the probable causes for each fault indication, and the right-
hand column which lists the procedure to isolate and correct the fault.  Use a digital multimeter to 
perform voltage and resistance measurements. 

 

 

Содержание Bently Nevada 7200 Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды