GE Becker VRP-B-1000-CH Скачать руководство пользователя

Страница: 32 / 36

29 | GE Oil & Gas

Figure 21: Inserting the seal neck

1000/1500-CH Seal Neck Assembly

Slide – 141 O-ring (A) over the cartridge cap (B). Slide –115 O-ring
(C) over the seal neck (D). Thread seal neck (D) into the cartridge
cap (B).

1000/1500-CH Cap Assembly

Pull the adjusting screw (E) up while threading the cartridge cap

(B) counter-clockwise. After the cap (B) is firmly engaged, turn

the adjusting screw (E) clockwise while pushing the cap (B) down.

When firm engagement of the cap (B) is felt, orient the cap (B) so

that the mounting holes are in line with the top body assembly (F)

pressure ports. Bolt the cap assembly (B) to the spring chamber

(G) using twelve (12), 1/4-20 x 3/4-inch HHCS (H).

Figure 22: Bolting the cap to the spring chamber

1000/1500-CH Thread Seal Assembly

Place 7/16-inch SS thread seal (I) and 7/16-inch SS flat washer (J)

onto the adjusting screw (E). After all necessary adjustments on

the pilot are made, thread the 7/16-inch SS jam nut (K) onto the

adjusting screw (E). Be careful because overtightening the jam nut

(K) may cause damage to the adjusting screw (E).

Figure 23: Finalizing the assembly

List of Recommended Tools:

1. Allen wrench. Sizes: 9/64-inch, 3/16-inch, 1/8-inch

2 Open wrench. Sizes: 7/16-inch, 3/4-inch, 11/16-inch, 5/16-inch

3. Socket wrench. 3/8-inch drive. Sizes: 7/16-inch, 3/4-inch

(Deepwell 12 PT.)

4. 6-inch adjustable wrench

5. Screwdriver models: Phillips head, standard

6. Soft blow hammer

7. General assembly grease

8. Torque wrench. 3/8-inch drive

1000/1500-CH Cap Assembly

Содержание Becker VRP-B-1000-CH


































Результаты поиска

Содержание Becker VRP-B-1000-CH

Отзывы:

Похожие инструкции для Becker VRP-B-1000-CH

Бренды по названию

Популярные бренды

GE Becker VRP-B-1000-CH, Инструкция по эксплуатации

Результаты поиска

Содержание Becker VRP-B-1000-CH

Отзывы:

Похожие инструкции для Becker VRP-B-1000-CH

Бренды по названию

Популярные бренды