GE Becker VRP-B-1000-CH Скачать руководство пользователя | Manualshive

Страница: 23 / 36

background image

Becker VRP-B-CH Series Valve Regulator Pilot Instruction Manual | 20

© 2016 General Electric Company. All rights reserved.

7. Attach the 1/4-28 jam nut (FF) to the valve adjusting screw (H).

7a. Screw the adjusting drum (GG) on the screw (H) and fasten

it with the 5-40 x 1/4 SHCS (HH1) threaded into the valve
adjusting screw (H).

Note: The jam nut (FF) showed should be located against the drum
(GG).

8. Center the pilot posts in the pilot body block (F) by:

8a. Rotating the diaphragm assembly (from steps 5 and 6)

counterclockwise until it stops (I).

8b. Marking the diaphragm and the pilot body block (F) with a

single line.

8c. Rotating the diaphragm assembly clockwise until it stops

(III).

8d. Marking the pilot body block (F) with a line extending from

the existing line on the diaphragm.

8e. Centering the line on the diaphragm between the two

existing lines on the pilot body block (II).

8f. Keeping the diaphragm secure in the center of the lines,

fasten the sensitivity spacer (JJ) to the pilot body block
(F) with six 1/4-20 x 3/4 HHCS (HH). This will secure the
diaphragm and prevent it from moving it any further.

8g. Place the lexan cover (DD1) in the outside of the sensitivity

spacer (JJ).

Note: The cutout should face the orifice block’s supply port (K).

FF

GG

F

K

N

HH1

H

W

F

III

I

DD1

HH

JJ

II

«
...
21
22
23
24
25
...
»

Содержание Becker VRP-B-1000-CH





































Отзывы:

Нет отзывов

Похожие инструкции для Becker VRP-B-1000-CH

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: National Instruments Страницы: 2

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: Ziton Страницы: 36

Бренд: Watlow Страницы: 20

Бренд: Greenheck Страницы: 4

Бренд: Vector Страницы: 8

Бренд: CAME Страницы: 128

Comfort System Z-300-HC

Бренд: Jackson Systems Страницы: 2

Бренд: HANYOUNG NUX Страницы: 4

Бренд: CALEFFI Страницы: 8

Бренд: Roger Страницы: 2

Бренд: Paradox Страницы: 28

Бренд: TREND Страницы: 4

Бренд: Autotrol Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды