GE Agile P50 Series Скачать руководство пользователя страница 71

Страница: 71 / 268

P50 Agile P153

5 Configuration

P153/EN M/B

5-33

Test LEDs

No Operation

Editable setting
By using the (

) or (

) key, Test LEDs can be set for No Operation /

Apply Test.

2.3.16

Group 1 Menu

2.3.16.1

Edit Settings

GROUP 1

Password protected window for “GROUP 1’’ settings:
SYSTEM CONFIG, OVERCURRENT, NEG SEQUENCE O/C, BROKEN

CONDUCTOR, EARTH FAULT 1, EARTH FAULT 2, THERMAL

OVERLOAD, COLD LOAD PICKUP, UNDERCURRENT and CB FAIL.
Note: Group 1 Setting will be seen only when it is enabled in

Configuration setting.

SYSTEM CONFIG

Password protected window for System Configuration i.e. 2nd

Harmonic (Disabled/Enabled), 2ndHarm Thresh and I>lift 2H.
Note: Setting will be seen only when it is enabled in Configuration

OVERCURRENT

Password protected window for Overcurrent i.e. I>1 Function, I>2

Function and I>3 Function. The functions can be set as Disabled / DT /

IDMT.
Note: Setting will be seen only when it is enabled in Configuration

NEG SEQUENCE O/C

Password protected window for Negative Sequence O/C i.e. I2>1

Function, I2>2 Function and I2>3 Function. The functions can be set as

Disabled / DT / IDMT.
Note: Setting will be seen only when it is enabled in Configuration

setting.

BROKEN CONDUCTOR

Password protected window for Broken Conductor i.e. BC Alarm

(Enable/Disabled), I2/I1 Setting - 1 and I2/I1 Time Dly – 1, BC Trip

(Enable/Disabled), I2/I1 Setting - 2 and I2/I1 Time Dly - 2.

EARTH FAULT 1

Password protected window for Earth Fault 1 (measured) i.e. IN1>1

Function, IN1>2 Function and IN1>3 Function. The functions can be set

as Disabled / DT / IDMT.
Note: Setting will be seen only when it is enabled in Configuration

setting.

EARTH FAULT 2

Password protected window for Earth Fault 2 (derived) i.e. IN2>1

Function, IN2>2 Function and IN2>3 Function. The functions can be set

as Disabled / DT / IDMT.
Note: Setting will be seen only when it is enabled in Configuration

setting.

THERMAL OVERLOAD

Password protected window for Thermal Overload i.e. Characteristic

(Disabled/Single), Thermal Trip, Thermal Alarm, Time Constant 1 and K.
Note: Setting will be seen only when it is enabled in Configuration

setting.

Содержание Agile P50 Series













































































































































































































































































Результаты поиска

Содержание Agile P50 Series

Отзывы:

Похожие инструкции для Agile P50 Series

Бренды по названию

Популярные бренды

GE Agile P50 Series, Техническое руководство

Результаты поиска

Содержание Agile P50 Series

Отзывы:

Похожие инструкции для Agile P50 Series

Бренды по названию

Популярные бренды