manualshive.com logo in svg

GE Security 1200C, Руководство по установке

Поделиться
Скачать
GE Security 1200C Скачать руководство пользователя страница 8

 

4 

1200C-2000C Fire Alarm Control Panel, Repeater, and Black Box Installation Manual 

General installation and connection guidelines 

Where to install the control panel 

Make sure the installation location is free from construction dust and debris, and 
immune to extreme temperature ranges and humidity (see “Technical specifications” 
on page 32 for more information on the operating temperature and relative humidity 
specifications). 
Allow for enough floor and wall space so the panel can be installed and serviced 
without any obstructions. The cabinet should be mounted so that the user interface is 
at eye level. 

Recommended cables 

Recommended cables for your fire system are shown in the table below. For more 
detailed information on cable characteristics and requirements see “Appendix D: 
Cable specifications” on page 39. 

WARNING: 

Failure to use the recommended cable may impact system performance. 

Table 1: Recommended cables 

Cable 

Cable description 

Maximum cable length 

Mains cable 

3 x 1.5 mm 

N/A 

Loop cable 

Shielded, twisted pair cable 

2 km 

RS485 network cable 

CAT5 

800 m 

Fibre optic network cable  

ST duplex 50/125, 62.5/125, or 
100/140 

1.7 km (see note below) 

LON network cable 

CAT5 

1.5 km 

RS232 serial communication 
cable 

7-way RS232 null modem cable 
with full handshaking 

12 m 

 

Note: 

Under ideal conditions the maximum distance between nodes is 1.7 km, but an 

optical power budget calculation should be performed to determine the correct 
maximum distance for each site. 

Installing or replacing control panel modules 

WARNING: 

Always back up site data before installing or replacing modules. 

When control panel modules are replaced or additional modules installed, the control 
panel automatically reconfigures and all site data is lost. Always back up site data 
before installing or replacing modules. 

Содержание 1200C

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды