manualshive.com logo in svg

GE Security 1200C, Руководство по установке

Поделиться
Скачать
GE Security 1200C Скачать руководство пользователя страница 34

 

30 

1200C-2000C Fire Alarm Control Panel, Repeater, and Black Box Installation Manual 

Maintenance 

The following maintenance procedures should be performed. by qualified personnel 
adhering to the CEN/TS 54-14 standard and any applicable local authority laws. 

Fire system maintenance 

Your fire system must be regularly tested and serviced in order to ensure its reliable 
operation. The following maintenance routine is recommended. 

Daily Verification 

•  Check that the panel indicates normal operation. If it does not, check that any 

fault indicated is recorded in the log book and reported to the maintenance 
personnel. 

•  Check that any fault warning recorded the previous day has received attention. 

Quarterly Verification 

•  Check the log book entries and that any necessary action has been taken. 
•  Check the state of the batteries and corresponding connections. 
•  Visually inspect the fire panel for signs of moisture or other deterioration. 
•  Test the alarm, fault and ancillary functions of the fire panel. 

Annual Verification 

•  Carry out the recommended daily and quarterly inspection and test routines. 
•  Check each detector for correct operation in accordance with the manufacturer's 

recommendations. 

•  Visually inspect all cable fittings and equipment to ensure that no damage has 

taken place. 

•  Visually inspect all electrical connections to make sure that they are securely 

fastened, that they have not been damaged and that they are appropriately 
protected. 

•  Visually inspect the manual call points, detectors and sounders to ensure that no 

structural or occupancy changes have affected their location requirements. 

Cleaning the control panel 

Keep the control panel clean inside and outside. Carry out periodic cleaning using a 
damp cloth for the outside.  
Do not use products containing solvents to clean the unit. Do not clean the inside 
with liquid products. 

Содержание 1200C

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды