manualshive.com logo in svg

GE Security 1200C, Руководство по установке

Поделиться
Скачать
GE Security 1200C Скачать руководство пользователя страница 26

 

22 

1200C-2000C Fire Alarm Control Panel, Repeater, and Black Box Installation Manual 

Power and fault monitoring LEDs on the PS1200N 

The PS1200N includes five LEDs for power and fault monitoring.  

Figure 20: PS1200N power and fault monitor LEDs 

 

1. Power LED 
2. Earth fault LED 
3.  Charger fault LED 
4.  Battery voltage fault LED 
5.  Battery circuit resistance fault LED 

 

LED Colour 

Description 

Power 

Green 

Indicates the power supply status and power source. If the LED 
is lit, then the is powered by the PS2000N power supply unit. If 
the LED is off, then the power is supplied by batteries or the 
module is without power. 

Earth fault 

Yellow 

Indicates control panel earth faults. If the LED is lit, an earth 
fault has been detected. 

Charger fault 

Yellow 

Indicates the general status of the battery charger. If the LED is 
lit, there is a fault with charging the batteries (incorrect voltage, 
temperature sensor connection fault, microcontroller error etc.) 

Battery voltage fault 

Yellow 

Indicates battery voltage faults. If the LED is lit, the battery 
voltage is less than 21V, there are no batteries connected, or 
there is a short circuit at the battery terminals. 

Battery circuit resistance 
fault 

Yellow 

Indicates the results of a battery circuit resistance test. If the 
LED is lit, the battery resistance is too high. 

 

Содержание 1200C

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды