manualshive.com logo in svg

GE Security 1200C, Руководство по установке

Поделиться
Скачать
GE Security 1200C Скачать руководство пользователя страница 43

 

1200C-2000C Fire Alarm Control Panel, Repeater, and Black Box Installation Manual 

39 

Appendix D: Cable specifications 

Mains 

power cable 

The recommended mains cable is 3 x 1.5 mm² (live, neutral, earth). 

Loop cable 

A twisted pair cable is required to ensure data integrity. Shielded, fireproof cable is 
highly recommended. If shielded cable is used, then cable shield continuity should be 
observed. 

 
Maximum cable length 

2 km (cable Ø 1 mm) 

Maximum cable capacitance 

300 nF / km 

Maximum total resistance 

100

Ω

 

 

RS485 network cable 

The recommended cable is CAT5 with a characteristic impedance of 100 

Ω

. 

Note: 

If the total cable length for the network exceeds 800 m and / or 32 nodes, we 

recommend the use of fibre-optic cabling. 
End-of-line termination resistors need to be used to match the cable characteristic 
impedance to prevent reflections 

 
Maximum cable length (bus and dual bus 
topology) 

800 m 

Maximum number of nodes (bus and dual bus 
topology) 

32 

When shielded cable is used, shields must be earthed at one point only. The shield of 
the cable must be continued between nodes using the terminal provided on the card.  

Fibre-optic network cable 

The recommended fibre-optic cable is a straight tip (ST) duplex with a fibre width of 
50/125, 62.5/125 or 100/140 µm. 
Fibre-optic networks may use more than 32 nodes. The maximum distance between 
nodes under ideal conditions is 1.7 km, but an optical power-budget calculation 
should be performed to determine the correct maximum distance for each site. 

Содержание 1200C

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды