manualshive.com logo in svg

GE Multilin 469, Инструкция по эксплуатации

Поделиться
Скачать
GE Multilin 469 Скачать руководство пользователя страница 225

CHAPTER 5: SETTINGS

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

5–83

5.11.4 Underpower

PATH: SETTINGS 

ZV

 S10 POWER ELEMENTS 

ZV

 UNDERPOWER

If enabled, once the magnitude of 3

Φ

 total power falls below the Pickup Level for a period 

of time specified by the Delay, a trip or alarm will occur. The Underpower element is active 
only when the motor is running and will be blocked upon the initiation of a motor start for a 
period of time defined by the 

BLOCK ELEMENT FROM START

 settings (e.g. this block may be 

used to allow pumps to build up head before the underpower element trips or alarms). A 
value of 0 means the feature is not blocked from start. If a value other than 0 is entered, 
the feature will be disabled when the motor is stopped and also from the time a start is 
detected until the time entered expires. The pickup level should be set lower than motor 
loading during normal operations.

For example, underpower may be used to detect loss of load conditions. Loss of load 
conditions will not always cause a significant loss of current. Power is a more accurate 
representation of loading and may be used for more sensitive detection of load loss or 
pump cavitation. This may be especially useful for detecting process related problems.

„

 

UNDERPOWER

[

BLOCK UNDERPOWER

FROM START: 0 s

Range: 0 to 15000 s in steps of 1

MESSAGE

UNDERPOWER

ALARM: Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN ALARM 

RELAYS:

Range: Alarm, Alarm & Auxiliary2, 

Alarm & Aux2 & Aux3, Alarm & 
Auxiliary3, Auxiliary2, Aux2 & 
Aux3, Auxiliary3

MESSAGE

UNDERPOWER ALARM

LEVEL: 2 kW

Range: 1 to 25000 kW in steps of 1

MESSAGE

UNDERPOWER ALARM

DELAY: 1 s

Range: 1 to 30 s in steps of 1

MESSAGE

UNDERPOWER ALARM

EVENTS: Off

Range: On, Off

MESSAGE

UNDERPOWER

TRIP: Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN TRIP 

RELAYS:

Range: Trip, Trip & Auxiliary2, Trip & 

Aux2 & Aux3, Trip & Auxiliary3

MESSAGE

UNDERPOWER TRIP

LEVEL: 1 kW

Range: 1 to 25000 kW in steps of 1

MESSAGE

UNDERPOWER TRIP

DELAY: 1 s

Range: 1 to 30 s in steps of 1

Содержание 469



















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды