manualshive.com logo in svg

GE Multilin 469, Инструкция по эксплуатации

Поделиться
Скачать
GE Multilin 469 Скачать руководство пользователя страница 135

CHAPTER 4: INTERFACES

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

4–45

4.6.5

Event Recorder

The 469 event recorder can be viewed through the EnerVista 469 Setup software. The 
event recorder stores generator and system information each time an event occurs (e.g. 
breaker failure). A maximum of 256 events can be stored, where E256 is the most recent 
event and E01 is the oldest event. E01 is overwritten whenever a new event occurs. Refer 
to 

Event 01 to Event 256

 on page 6–33 for additional information on the event recorder.

Use the following procedure to view the event recorder with EnerVista 469 Setup:

With EnerVista 469 Setup running and communications established, 

Z

Select the 

Actual > A4 Event Recorder

 item from the main menu. 

This displays the Event Recorder window indicating the list of recorded 
events, with the most current event displayed first.

FIGURE 4–9: Event Recorder Window

To view detailed information for a given event and the system information at the moment 
of the event occurrence, 

Z

Change the event number on the 

Select Event

 box.

EVENT LISTING

Lists the last 256  events
with the most recent
displayed at top of list.

EVENT SELECTION

Select an event row to
view event data information,
which will be displayed in the
window to the right

CLEAR EVENTS

Click the Clear
Events button to
clear the event list
from memory.

SAVE EVENTS

Click the Save Events
button to save the event
record to the PC as a
CSV file.

EVENT DATA

System information as
measured by the relay
at the instant of the
event occurrence.

DEVICE ID

The events shown here
correspond to this device.

EVENT NUMBER

The event data information
is related to the selected
event is shown

Содержание 469



















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды