manualshive.com logo in svg

GDC PSD-3000-P, Руководство по установке

Поделиться
Скачать
GDC PSD-3000-P Скачать руководство пользователя страница 5

 

 

 

4 

 

Thank you for purchasing a GDC SX-3000 Standalone

 

Integrated Media 

Block™ and PSD-3000-P Portable Storage Device from GDC Technology 
Limited.

 

 

To ensure proper operation and to maximize the  SX-3000 and PSD-3000-P value, please review this 
User Manual. It will guide you through all the features and benefits of the new  SX-3000 Standalone 
Integrated Media Block™.  

 

COPYRIGHT NOTICE

 

Copyright ©  2013 by GDC Technology Limited 

All rights reserved. No part of this manual may be copied or distributed, transmitted, transcribed, stored in a 
retrieval system, or translated into any human or computer language, in a form or by any means, electronic, 
mechanical, photocopying, recording, magnetic, optical, manual or otherwise, or disclosed to third parties 
without prior written permission of GDC Technology Limited. 

 

MANUAL DISCLAIMER

 

This manual is made with SMS version 9.0 and there might be slight differences depending on the software 
version the IMB is running. The contents, features and specifications stated in this manual are subject to 
change without notice due to continuous product development and improvements. In no other event shall 
GDC Technology Limited be liable for any loss of profit or any other commercial damages, including but not 
limited to special, consequential, or other damages. 

 

NOTE: 

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of the 

following measures: 

 

•    Reorient or relocate the receiving antenna. 

•    Increase the separation between the equipment and receiver. 

•    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

•    Consult the dealer or an experienced radio/TV technician for help. 

 

 

 

Содержание PSD-3000-P

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды