manualshive.com logo in svg

GDC PSD-3000-P, Руководство по установке

Поделиться
Скачать
GDC PSD-3000-P Скачать руководство пользователя страница 25

 

 

 

24 

 

 

3. 

Hold the front of door and rotate the door to the right.  

 
 
 
 
 
 
 
 
 

4. 

Pull the door aside so that it is in 90° angle of the device. Now, the HDD can be taken out or 
put in. (The door shall be close in the opposite steps)  

 
 
 
 
 
 
 
 
 
 

Caution: 

 

Please gently push the door when closing to avoid damage to the component.  

 

If the HDD is inserted incorrectly, please do not close the HDD tray door. Forcing the door to 
close will damage the machine. 

 

Procedure to Uninstall the HDD 

I.  Release the triangle lock by using the key (Rotate 90 degrees Clockwise) and open the HDD 

tray door. 

II.  Take out the HDD from HDD tray and close the door. Lock the HDD tray by using the key. 

(Rotate 90 degrees Counterclockwise) 

Caution: 

 

The label should be facing up; the connector should be faced down in order to insert the HDD 
into the HDD tray. HDD cannot be inserted if it is in the wrong direction. 

 

Do not take out the HDDs during operation. 

 

The temperature of HDDs may exceed 50

 O

C. Please handle carefully. 

 

 

 

Содержание PSD-3000-P

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды