background image

Page 4 - 18

Installation

Digital Feeder  Operation and Maintenance  Manual

 © GBC Pro - Tech February 2000

c) Push the opposite end of the pneumatic tube

into the air fitting of the cutter located below the
main power ON/OFF.

When finished with all of the

necessary connections, zip ties should be
used to neatly route the cables, pneumatic
hoses and cords. This will prevent
entanglement with these items while
working around the system.

INFORMATION

D o   n o t   p i n c h   t h e   p n e u m a t i c   t u b i n g   w h e n

using zip ties to route. Pinching will

constrict the air flow.

4.9   Safety check

The safety check will ensure that all safety devices

and interlock switches are functioning properly. Refer to
Section 5 Operations for detailed explanation of the
control panel.

W A R N I N G

Do not wear ties, loose fit clothing or

dangling jewelry while operating or

servicing the feeder. These items can
get caught in the machine and choke

you or you can be crushed.

W A R N I N G

If a safety feature is not functioning

properly, contact your local service

representative immediately

Safety on the feeder consists of the sheet table

upper limit switch, sheet table lower limit switch and an
emergency stops ( E-STOP ). Do not have the laminator
webbed.

INFORMATION

The Explorer 107 and the Digital Feeder

must both have power turned to ON.

Содержание 930 - 042























































































Отзывы: