GatesAir Intraplex MA-311, Руководство по установке и эксплуатации

Страница: 19 / 37

2 – Functional Description & Setup Intraplex VF-40 Voice Module
Version 1.11
GatesAir 2-9
Intraplex Products
Table 2-5. Module Address Setting – SW3
Switch
Positions*
1 2 3 4 5 6 Switch
Positions*
1 2 3 4 5 6
1 0 0 0 0 0 1 19 0 1 0 0 1 1
2 0 0 0 0 1 0 20 0 1 0 1 0 0
3 0 0 0 0 1 1 21 0 1 0 1 0 1
4 0 0 0 1 0 0 22 0 1 0 1 1 0
5 0 0 0 1 0 1 23 0 1 0 1 1 1
6 0 0 0 1 1 0 24 0 1 1 0 0 0
7 0 0 0 1 1 1 25 0 1 1 0 0 1
8 0 0 1 0 0 0 26 0 1 1 0 1 0
9 0 0 1 0 0 1 27 0 1 1 0 1 1
10 0 0 1 0 1 0 28 0 1 1 1 0 0
11 0 0 1 0 1 1 29 0 1 1 1 0 1
12 0 0 1 1 0 0 30 0 1 1 1 1 0
13 0 0 1 1 0 1 31 0 1 1 1 1 1
14 0 0 1 1 1 0 32 1 0 0 0 0 0
15 0 0 1 1 1 1 33 1 0 0 0 0 1
16 0 1 0 0 0 0 34 1 0 0 0 1 0
17 0 1 0 0 0 1 35 1 0 0 0 1 1
18 0 1 0 0 1 0 36 1 0 0 1 0 0
* 0 = OFF, 1 = ON
The VF-40 module reports itself as a TYPE 142 card. Its remote operation involves the use of "P"
(parameter) codes and “S” (status) codes (Sections 2.7.1 and 2.7.2).
2.7.1 P Codes
P codes, when used in the parameter field of a
SET
command, allow the user to set parameters on the
module by remote control, just like setting the switches on a module under local control. There are
fourteen P codes for the VF-40 module, P1 through P14. Each is a number from 0 to 255, also
represented as an eight-digit binary number (in parentheses). The first four P codes, P1 through P4,
provide remote access to the settings controlled by the dip switches on the module itself, as well as
allowing activation of the remote loopback feature. The remaining eight codes, P5 through P12, are
used to change the input and output level settings for each of the four voice channels on the module.
Table 2-6 describes the meanings of the P codes in detail. P codes also appear in the response to a
CONFIG?
query, showing the current parameter settings on the module.
Note: When using binary numbers in the parameter field of a
SET
command, they must be preceded
by the letter “B”, for example:
<MULTIPLEXER ADDRESS>:<CARD ADDRESS>:SET:P02 = B00000001;
In addition to the P codes, you can also turn service on or off for the module by sending
SRVC = ON
or
SRVC = OFF
in the ISiCL parameter field with a
SET
command.