Gaspardo SD, Использование и обслуживание

Страница: 44 / 48

USE AND MAINTENANCE
42
ENGLISH
cod. 19501980
g
5.0.5. EVERY SIX MONTHS
- Oil the height adjuster screw and the tilted rear wheel screw
(4 Fig. 44).
- Grease the self-aligning bearings of the drive wheels.
- Grease the bevel gear pair of the Cardan shaft (5 Fig. 44).
5.0.6. REST PERIODS
At the end of the season, or if a long period of rest is foreseen
it is advisable to:
- Wash the equipment thoroughly with water, especially the
chemical substance hoppers, then dry them.
- Carefully check for worn or damaged parts and replace then
where required.
- Adjust the belt of the diffusion air pump and and replace it if
necessary.
- Firmly tighten all screws and bolts.
- Oil all the drive chains and apply lubricant to all unpainted
parts.
- Protect the equipment with a (nylon) cover.
- Then position it stably in a dry place out of the reach of
unauthorized people.
It is in the interests of the user to follow these instructions
carefully, as when work recommences, he will find the equipment
in perfect condition.
6.0 FOLDING FRAME (SDI)
The seeder is suitable only for the uses indicated. Any
other use different from that described in these
instructions could cause damage to the machine and
represent a serious hazard for the user.
Regular operation depends on the correct use and adequate
maintenance of the equipment. It is advisable therefore to
observe scrupulously what is described in order to prevent any
inconveniences that could prejudicate proper operation and
duration. It is just as important to keep to what is described in
this booklet since the Manufacturer declines all responsibility
due to negligence and non-observance of these rules.
At any rate the Manufacturer is available to assure immediate
and accurate technical assistance and all that may be necessary
for the improved operation and better performance of the
equipment.
Check that the quick hook-ups are coupled correctly; parts
of the system could get damaged if they are not.
ATTENTION
Oil escaping at high pressure can cause skin injury with
the risk of serious wounds and infection. Call a doctor
immediately if such an incident occurs. Therefore, the
installation of hydraulic components in the tractor driver's
cab is strictly forbidden.
All the components of the system should be positioned
carefully to avoid parts being damage during use of the
equipment.
6.1 DESCRIPTION OF FUNCTIONING
The machine frame is designed so that the side ends that hold
the planting elements can be folded using a hydraulic system,
thus reducing the road.
The hydraulic folding parts of the planter are floating and allow
you to work on ground that is not perfectly flat. The side parts
of the frame, in fact, can move down with respect to the central
one by approx. 7 centimetres.
They are moved by double-acting hydraulic cylinders,
independently of each other. To adjust the speed of rise and fall
of the side frames it is necessary to adjust the valve located on
each hydraulic delivery pipe, as explained in chapter 8.0.
DANGER
When opening and closing of the folding frame, do not
under any circumstances stand close to the machine.
In order to use correctly the toolbar of the planter, operate as
follows:
1) Hook the planting unit to the tractor three-point coupling
using suitably sized pins equipped with the necessary safety
devices (retainer clips, spring pins, etc.).
2) Connect the planting unit hydraulic pipes to the tractor
distributors (see chapter 8.0).
3) Before switching the machine on, make sure that there are
no people, children, animals or any object that could get in
the way of the machine, and ensure that there is excellent
visibility in the area of operation.
OPENING
4) Unhook the safety pins on the frame (A Fig. 45) and place
them in their relative seats (B Fig. 45).
5) Check that the hydraulic pipes are correctly connected (see
chapter 8.0).
6) Actuate the hydraulic system to open the frame, keeping
the planter raised from the ground.
CLOSING
7) Activate the hydraulic system to close the frame, keeping
the planting unit raised off the ground and with the seeders
hooked into the raised position.
8) Hook the frame safety pins into their relative seats (A Fig.
45).
9) Discharge the pressure in the hydraulic system and disconnect
the hydraulic pipes.
B
A
fig. 45