Garten Meister GM-LB2600, Перевод оригинального руководства пользователя

Страница: 29 / 80

GB | 29
Check before use!
• Check the safe condition of the device:
• Check the device for leaks.
• Check the device for visual defects.
• Check that all parts of the device have been se-
curely fitted.
• Check that all safety devices are in proper condi-
tion.
Starting the blower
• To start the Blower Ensure that the intermediate
suction/blower tube is fitted correctly
• To use the appliance follow the motor starting in-
structions as described in the operating instruc-
tions.
• Make sure that nothing is covering the exhaust
pipe as this would cause heat to build up.
• Hold the handle firmly with your right hand and
swing the nozzle back and forth so that the desired
area is cleared of contamination.
• The throttle lever and the on / off switch are inte -
grated in the handle.
• With the throttle lock, the engine can be locked at
full throttle without constantly pressing the throttle.
Caution: Before switching off the device, push the
throttle lock to idle
PREPARE THE MACHINE
The machine can be used as both a blower and a
vacuum collector (vacuum function on 28BVSP only);
for both of these uses it is necessary to correctly ar-
range the appropriate accessories included with the
equipment.
Warning : Unpacking and completing the assembly
should be done on a flat and stable surface, with
enough space for moving the machine and its pack-
aging, always making use of suitable equipment.
IMPORTANT The safety systems prevent the engine
from starting if the vacuum or blower tubes are not
assembled correctly.
USE AS A BLOWER
• Remove the screw (1) and its washers (2).
• Align the first blower tube compartment (3) with the
protrusion (4) of the air outlet, push the tube and
turn it 90° clockwise, in order to permanently fix it
in place.
• Fix the tube (3) to the air outlet using the screw (1)
and its washers (2).
• Align the second blower tube compartment (5) with
the protrusion (6) of the first tube, push the tube
and turn it 90° clockwise, in order to permanently
fix it in place.
NOTE The machine is correctly assembled when the
flat part of the blower chute is pointed towards the
ground. The engine can not start if you do not as-
semble the blower tube when using as a blower.
USE AS A VACUUM COLLECTOR
• Remove the screw (1) and its washers (2).
• Align the housing of the bag tube (3) with the pro-
trusion (4) of the air outlet, push the tube and turn
it 90° anticlockwise, in order to permanently fix it
in place.
The machine is correctly assembled when the tube’s
terminal chute is pointed downwards and to the left of
the operator
• Fix the tube (3) to the air outlet using the screw (1)
and its washers (2).
• Loosen the knob (5) and open the protection grille
(6).
• Align the first vacuum tube compartment (7) with
the protrusion (8) of the inlet, push the tube and
turn it 90° clockwise, in order to permanently fix it
in place.
• Align the second vacuum tube compartment (9)
with the protrusion (10) of the first tube, push the
tube and turn it 90° clockwise, in order to perma-
nently fix it in place.
The machine is correctly assembled when the round-
ed part of the chute is pointed towards the ground.
• Insert the bag tube end (3) in to the bag (11) and
close the opening with the supplied Velcro strap
(12).
• Hang the bag over your shoulder and adjust the
height using the strap.
The engine can not start if you do not assemble
the vacuum tube when using as a vacuum.
CHECKING THE MACHINE
Before starting work please:
• check that all the screws on the machine are tightly
fastened;
• when used as a vacuum collector, make sure the
bag is fitted correctly and that the zip is closed;
• check that the air filter is clean;
• check that the hand grips are well fastened;
• prepare accessories according to the type of work
(as blower or vacuum collector) and make sure
they are correctly mounted;
• fill with fuel as indicated below.
Start (Fig 6)
Once the machine has been set up properly, start
the engine as follow:
1 Turn the engine switch(1) to the ON position (E).
2 Put the choke lever(11) on the position .
3 Press the fuel pump(10) more than 5 times(G).
4 Pull the recoil starter handle (8) 3-5 times to start
the engine.
5 Once the motor is running, briefly wait, then put
the choke lever(11) into position .