25
Command Number 232:
Zone No. Assign. to Input No. 5 of Expander Module No. 2
Default values ------------------------------------------------------------------------------> 0 0
2
3
2
Positions -------------------------------------------------------------------------------------> (1) (2)
Command Number 233:
Zone No. Assign. to Input No. 6 of Expander Module No. 2
Default values -----------------------------------------------------------------------------> 0 0
2
3
3
Positions --------------------------------------------------------------------------------------> (1) (2)
Command Number 234:
Zone No. Assign. to Input No. 7 of Expander Module No. 2
Default values -----------------------------------------------------------------------------> 0 0
2
3
4
Positions --------------------------------------------------------------------------------------> (1) (2)
Command Number 235:
Zone No. Assign. to Input No. 8 of Expander Module No. 2
Default values -----------------------------------------------------------------------------> 0 0
2
3
5
Positions -------------------------------------------------------------------------------------> (1) (2)
Command Number 236:
Assign. of Zone No. to Module Input No.1 Expander N° 3
Default values ------------------------------------------------------------------------------> 0 0
2
3
6
Positions --------------------------------------------------------------------------------------> (1) (2)
Digit position (1)-(2):
Assignment of Zone No. to Input No. 1 of Expander Module No. 3
The code must be 2 digits long. Valid values are 00 to 32.
Note:
With the value [00] the zone is bypassed.
Note:
Commands 237 to 243 (Assignment of zone no. to entry no. 1 of the
module (module expander No. 3) are programmed in the same way as command No.
236.
Command Number 237:
Zone No. Assignment to Input No. 2 of Expander Module No. 3
Default values ------------------------------------------------------------------------------> 0 0
2
3
7
Positions -------------------------------------------------------------------------------------> (1) (2)
Command Number 238:
Zone No. Assign. to Input No. 3 of Expander Module No. 3
Default values ------------------------------------------------------------------------------> 0 0
2
3
8
Positions -------------------------------------------------------------------------------------> (1) (2)
Command Number 239:
Zone No. Assign. to Input No. 4 of Expander Module No. 3
Default values -----------------------------------------------------------------------------> 0 0
2
3
9
Positions -------------------------------------------------------------------------------------> (1) (2)
Command Number 240:
Assign Zone No. to Input No. 5 of Expander Module No. 3
Default values -----------------------------------------------------------------------------> 0 0
2
4
0
Positions --------------------------------------------------------------------------------------> (1) (2)
Command Number 241:
Zone No. Assign. to Input No. 6 of Expander Module N. 3
Default values ------------------------------------------------------------------------------> 0 0
2
4
1
Positions --------------------------------------------------------------------------------------> (1) (2)
Command Number 242:
Zone No. Assign. to Input No. 7 of Expander Module N. 3
Default values ------------------------------------------------------------------------------> 0 0
2
4
2
Positions -------------------------------------------------------------------------------------> (1) (2)
Command Number 243:
Zone No. Assign. to Input No. 8 of Expander Module N. 3
Default values ------------------------------------------------------------> 0
0
2
4
3
Positions -----------------------------------------------------------------------------------> (1) (2)
Command Number 244:
Auxiliary Fault Counter
Default values
------------------------------------------------------------------------------> 0 8
2
4
4
Positions -------------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Auxiliary Fault Counter.
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note:
If you program 00 the equipment will not monitor the fault.
Command Number 245:
Auxiliary Fault Counter BUS-D485
Default values
----------------------------------------------------------------------------> 0 8
2
4
5
Positions --------------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Auxiliary Fault Counter BUS-D485
The code must be 2 digits long. Valid values are 00 to 16.
Note:
If you program 00 the equipment will not monitor the Fault.
Command Number 246:
Battery Failure Counter
Default Values -----------------------------------------------------------------------------> 0 8
2
4
6
Positions --------------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Battery Failure Counter
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note:
If you program 00 the equipment will not monitor the fault.
Command Number 247:
Siren Fault Counter
Default values
----------------------------------------------------------------------------> 0 8
2
4
7
Positions -----------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Siren Fault Counter
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note:
If you program 00 the equipment will not monitor the fault.
Command Number 249:
Expander Module Failure Counter
Default values
-----------------------------------------------------------------------------> 0 8
2
4
9
Positions --------------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Counter Failure Expander Modules
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note:
If you program 00 the equipment will not monitor faults.
Command Number 250:
Auxiliary Source Fault Counter
(Supervisory, Mains and Low Battery Fault)
Default values -----------------------------------------------------------------------------> 0 8
2
5
0
Positions -------------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Fault Counter Auxiliary source
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note:
If you program 00 the equipment will not monitor faults.
Note:
The programmed value is valid for Supervisory, Mains and Low Battery faults.
Command Number 251:
Manual Test Report Counter
Default values
-----------------------------------------------------------------------------> 0 8
2
5
1
Positions -------------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Counter Manual Test Report
The code must be 2 digits long. Valid values are 00 up to 16 events.
Command Number 252:
Wifi Module Fault Counter
Default values -----------------------------------------------------------------------------> 0 8
2
5
2
Positions -------------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Counter Wifi Module Failure
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note:
If you program 00 the equipment will not monitor the fault.
Command Number 253:
Network Fault Counter
Default values
-----------------------------------------------------------------------------> 0 8
2
5
3
Positions -----------------------------------------------------------------------------------> (1) (2)
Digit position (1)- (2):
Mains Failure Counter
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note:
If you program 00 the equipment will not monitor the fault.
Содержание PC-900G
