Garmin GNS 480, Руководство по установке

Страница: 103 / 186

Post-Installation Configuration & Checkout
GNS 480 (CNX80) Installation Manual560-0982-01 Rev A 3-29
Table 3-6 – Description of Input Monitor Items
Display Label
(cyan)
Signal Name Connector – Pin(s)
Expected Display
(white)
429 IN 1:
429 IN 2:
429 IN 3:
ARINC 429 IN 1
ARINC 429 IN 2
ARINC 429 IN 3
P5-7,27
P5-8,28
P5-9,29
‘FFFFFFFF’ will be displayed if no data has been received.
The hex value of the most recently received label will be
displayed if data is being received.
‘00000000’ will be displayed if data was received, but no
data has been received in the last 5 seconds.
P1-14: Com Flip Flop In P1-14
‘0’ in input is open
‘1’ if input is grounded
P1-15: UP Discrete In P1-15
‘0’ in input is open
‘1’ if input is grounded
P1-33: DOWN Discrete In P1-33
‘0’ in input is open
‘1’ if input is grounded
P1-34: VOR Flip Flop In P1-34
‘0’ in input is open
‘1’ if input is grounded
P5-36: OBI Select In P5-36
‘0’ in input is open
‘1’ if input is grounded
P5-56: RESERVED P5-56
‘0’ in input is open
‘1’ if input is > 9 VDC
P5-57: Heading Valid In P5-57
‘0’ in input is open
‘1’ if input is > 9 VDC
P5-72: RESERVED P5-72
‘0’ in input is open
‘1’ if input is grounded
P5-73: RESERVED P5-73
‘0’ in input is open
‘1’ if input is grounded
P5-74: RESERVED P5-74
‘0’ in input is open
‘1’ if input is grounded
P5-75: RESERVED P5-75
‘0’ in input is open
‘1’ if input is grounded
P5-76: Suspend In P5-76
‘0’ in input is open
‘1’ if input is grounded
P5-77: Audio Inhibit In P5-77
‘0’ in input is open
‘1’ if input is grounded
P5-78: RESERVED P5-78
‘0’ in input is open
‘1’ if input is grounded
P4-4: Com PTT P4-4
‘0’ in input is open
‘1’ if input is grounded
CDI SEL: Main CDI Select In P7-8
Normally a ‘-‘ is displayed. When the input is actuated a ‘T’
will be displayed for approximately 1 sec.
232-1:
232-2:
232-3:
422-4:
232-5:
232-6:
232-7:
232-8:
RS232 Port 1 In
RS232 Port 2 In
RS232 Port 3 In
RS422 Port 4 In
RS232 Port 5 In
RS232 Port 6 In
RS232 Port 7 In
RS232 Port 8 In
P1-4,23
P1-3,21
P1-7,25
P1-11,26
P5-1,41
P5-2,42
P5-10,44
P5-30,44
‘FF’ will be displayed if no data has been received.
The hex value of the most recently received data will be
displayed if data is being received.
‘00’ will be displayed if data was received, but no data has
been received in the last 5 seconds.
SYNCHRO HDG: Synchro Heading P5-18,19,38
If the synchro valid discrete is INVALID or the 26VAC,
400Hz reference is not present, ‘---‘ will be displayed;
otherwise, the angle of the synchro heading input will be
displayed.
BARO: Baro Correction Pot P5-13,33,53
The value of the baro potentiometer input will be displayed.
‘0’ will be displayed if input is open, or if the baro pot input
has not been properly calibrated.
26VAC 26 VAC Reference P5-20,39
The voltage and frequency of the 26VAC, 400Hz input will
be displayed. If this input is not connected, or if the voltage
is below 1VAC, ‘---‘ will be displayed.