Garmin GNC 300 Скачать руководство пользователя | Manualshive

Страница: 19 / 142

background image

Section 1

Navigation Key

The GNC 300 features six navigation pages to provide various position, course,

speed, status and planning information. The pages may be viewed by pressing the
NAV key and rotating the outer knob, or by pressing the

N

key repeatedly.

The

CDI

,

NAVCOM

and

position

pages are the primary pages used during in-

flight navigation, while the nav menu and status pages offer access to planning, calcu-
lation and status functions. Note that rotating the outer knob clockwise will continu-
ously cycle through all the nav pages, whereas turning the knob counterclockwise will
stop the page selection sequence at the CDI page.

Whenever the NAV key pages are in use, the indicator light (

U

) next to the NAV

key will illuminate. If the GNC 300 requires you to enter data on a navigation page,
the MSG indicator will flash and a message prompt with specific instructions will
appear. If you leave the NAV page sequence for another set of pages, the last NAV
page displayed will appear when you return to the nav sequence.

9

REFERENCE

NAV key overview

Remember!

The NAV pages will only display information

AFTER

the position and navigational information has

been calculated from the satellites. If you are on the
Position page before the unit has calculated a position, you
will be able to enter an approximate position and altitude.
This is helpful in speeding satellite acquisition if the unit
has moved a great distance with the power off.

If you are not sure the GPS is actively calculating position,
check the receiver status field for ‘2D NAV’ or ‘3D NAV’
by pressing the NAV key and rotating the outer knob until
the Satellite Status page appears. The current receiver sta-
tus is displayed at the top left of the page.

CDI page

NAV Menu 2

Position Page

NAV Menu 1

NAVCOM page

Satellite Status Page

SECTION

1

NAV KEY

Overview

300 7/14/98 8:49 AM Page 9

«
...
17
18
19
20
21
...
»

Содержание GNC 300















































































































































Отзывы:

Нет отзывов

Похожие инструкции для GNC 300

CN-NVD905U - Strada - Navigation System

Бренд: Panasonic Страницы: 11

Бренд: Javad Страницы: 16

Бренд: Teltonika Страницы: 14

Бренд: Westcoast GPS Страницы: 14

Бренд: Rosen Страницы: 16

Бренд: Leica Страницы: 48

aera 1900111700

Бренд: Garmin Страницы: 52

Бренд: Navman Страницы: 42

Бренд: Seiko Страницы: 58

Бренд: INTELINK Страницы: 11

Бренд: NavEye Страницы: 3

Бренд: Laipac Страницы: 64

Бренд: Qstarz Страницы: 2

Бренд: Qstarz Страницы: 4

BT-Q1200 Super 99

Бренд: Qstarz Страницы: 7

Бренд: Qstarz Страницы: 20

Бренд: Qstarz Страницы: 24

Бренд: Qstarz Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды