Garmin GNC 300 Скачать руководство пользователя

Страница: 115 / 142

To restore user data from a user data card to the GNC 300:

1. Install the user data card.

2. Rotate

to highlight ‘Restore user data?’.

3. Press

The GNC 300 will ask you which type of data to replace. You may choose check-

lists, scheduler messages, user waypoints, proximity waypoints, routes, waypoint
comments, or all data.

4. Rotate

to select the type of data to replace.

You may either replace or update the information in the database. Replacing the

data will replace

ALL

user data with the data from the card. Updating the data will

not delete unrelated material, but will only change what is necessary to use the data
received from the user data card.

5. Rotate

to select either ‘Replace?’ or ‘Update?’.

6. Press

to begin transferring data to the GNC 300. The GNC 300 will now transfer all

of the data requested. This may take a few minutes.

7. To continue with more data transfer types, repeat steps 4, 5 and 6. Otherwise, press

when ‘ok?’ is highlighted.

8. Turn the GNC 300 off and replace the user data card with a NavData card. The GNC 300 is

now ready for normal operation.

105

Getting Started

Status & Position

SECTION

NAVDATA CARD

Saving User Data

Restore Data Page

Data Transfer Page

300 7/14/98 8:51 AM Page 105

Содержание GNC 300















































































































































Результаты поиска

Содержание GNC 300

Отзывы:

Похожие инструкции для GNC 300

Бренды по названию

Популярные бренды

Garmin GNC 300, Руководство пилота

Результаты поиска

Содержание GNC 300

Отзывы:

Похожие инструкции для GNC 300

Бренды по названию

Популярные бренды