Garmin GNC 300 Скачать руководство пользователя | Manualshive

Страница: 114 / 142

background image

Appendix A

NavData

®

and User Data Installation and Operation

The NavData card supplied with your GNC 300 can be installed or removed

when the GNC 300 is on or off. Insert the card with the thumb tab at the top, and
the beveled corner at the bottom. If the NavData card is not present when the unit is
powered on, you will receive a ‘No Jeppesen database’ message on the database con-
firmation page, and you will only be able to use user waypoints for navigation. If the
NavData card is removed during operation, a ‘No data card present’ warning will
appear, asking you to reinsert the data card within 30 seconds. If the card is not
replaced within 30 seconds, the GNC 300 will automatically reinitialize. You may
also reinitialize the unit manually by pressing ENT.

An optional

user data card

can be used to make a backup of user waypoints,

routes, etc. and transfer information to another GNC 300.

To save user data to the user data card:

1. Install the user data card.

2. Rotate

O

to highlight ‘Save user data?’. Press

E

to confirm.

The message ‘Saving to card’ is displayed while the GNC 300 transfers all user

data to the User Data card. It may take a few minutes to complete the transfer. When
all user data is transferred, the GNC 300 will instruct you to turn the unit off, remove
the user card and insert the Jeppesen NavData card. After this is complete, the GNC
300 is ready for normal operation.

104

Getting Started

Status & Position

SECTION

A

NAVDATA CARD

Saving User Data

Insert the card with the thumb tab at the top, and
the beveled corner on the bottom right.

Data Card Warning

300 7/14/98 8:51 AM Page 104

«
...
112
113
114
115
116
...
»

Содержание GNC 300















































































































































Отзывы:

Нет отзывов

Похожие инструкции для GNC 300

Chart Master 169CSI

Бренд: Interphase Страницы: 89

GLOBALWATCH UAIS - QUICK

Бренд: ACR Electronics Страницы: 75

Бренд: SunTech Страницы: 7

Бренд: Wintec Страницы: 34

Бренд: Vastera Страницы: 22

Бренд: Garmin Страницы: 37

Бренд: I-gotU Страницы: 15

Бренд: Kestrel Страницы: 8

Бренд: SONAL TRACK Страницы: 11

Бренд: Garmin Страницы: 91

Бренд: Entec Solar Страницы: 47

Бренд: Garmin Страницы: 30

Бренд: Becker Страницы: 157

Бренд: GPS Страницы: 17

Бренд: RoyalTek Страницы: 7

Бренд: RoyalTek Страницы: 22

Бренд: RoyalTek Страницы: 23

Бренд: RoyalTek Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды