Garmin GNC 300 Скачать руководство пользователя | Manualshive

Страница: 124 / 142

background image

Route wpt moved

-

One or more route waypoints were moved at
least 0.33 arc minutes due to a database
change.

Searching the sky

-

The GNC 300 is in the search-the-sky mode.
Allow the unit to complete data collection
before turning it off.

Select auto seq mode

-

The GPS SEQ switch should be set to the
AUTO position to continue navigation.

Set course to ____º

-

The CDI/HSI should be set to the specified
course.

SID deleted -

The SID was deleted from the route because
of insufficient space in the route.

STAR deleted -

The STAR was deleted from the route because
of insufficient space in the route.

Start altitude chng

-

The altitude change entered on the VNAV
Planning page is about to begin.

Steep turn ahead

-

This message appears approximately 90 sec-
onds prior to a turn that requires a bank angle
in excess of 25 degrees in order to stay on
course. Turn anticipation will not be provided.

Stored data lost

-

Stored user data, including waypoints, routes
and satellite orbital data have been lost due to
a low memory battery or inadvertent master
reset.

Stuck mic/tx disabled

-

The microphone/headsets have been transmit-
ting continuously for 35 seconds, and the
transmitter has been disabled. Releasing the
transmit key will allow you to transmit again.
If this message permits, check the installation.

SUA ahead < 10 min

-

The projected course and current speed will
take you inside an SUA within the next 10
minutes.

SUA near & ahead

- Your position is within two nautical miles of

an SUA and its current course will take you
inside.

Timer expired

-

The approach timer has expired.

User data RX started

-

Data receive operations have started.

Usr data TX complete

-

Data transmit operations are complete.

VNAV cancelled

-

The VNAV function has been cancelled due to a
change in the active route.

WGS 84 datum selectd -

The system map datum was changed to
WGS 84 because the selected map datum
has been removed from the NavData card,
the data card is missing, or the data card has
failed.

Wpt comment locked

-

At least one waypoint comment is locked
because the waypoint has been removed
from the Jeppesen NavData®, the data card
is missing, or the data card has failed.

114

GETTING STARTED

Status & Position

SECTION

D

MESSAGES &

ABBREVIATIONS

300 7/14/98 8:51 AM Page 114

«
...
122
123
124
125
126
...
»

Содержание GNC 300















































































































































Отзывы:

Нет отзывов

Похожие инструкции для GNC 300

Бренд: Garmin Страницы: 8

Бренд: Gator Страницы: 11

Бренд: Gator Страницы: 15

Бренд: V-Sun Страницы: 19

Бренд: Ublox Страницы: 28

Yardage PRO 368100

Бренд: Bushnell Страницы: 36

Бренд: XT Страницы: 8

Бренд: Transplant Computing Страницы: 30

Бренд: Myto Страницы: 76

Бренд: Nokia Страницы: 9

Бренд: Nokia Страницы: 23

LD-3W - Wireless GPS Module

Бренд: Nokia Страницы: 68

LD-1W - GPS Module

Бренд: Nokia Страницы: 108

Бренд: Garmin Страницы: 132

Бренд: FCC Страницы: 6

Бренд: Zte Страницы: 47

Бренд: Audiovox Страницы: 12

Бренд: VDO Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды