Garland XE362S-2L Скачать руководство пользователя страница 35

Страница: 35 / 88

Part # JIBSM08 Rev.6 (08/04/09)

Page 35

TROUBLESHOOTING

ERROR MESSAGES:

NOTE: WE STRONGLY SUGGEST THAT ANY INSTALLATION,

MAINTENANCE AND REPAIRS SHOULD BE PERFORMED BY

YOUR LOCAL GARLAND AUTHORIZED SERVICE AGENCY .

PROBE ERROR:

...occurs when the probe is open or not connected. The

control will turn the heat off. If the fault is in the platen

the grill can still be used with recipes that do not call for

the platen. If the grill probe circuit is open, the grill will

not operate. The corresponding tri-color LED will turn red

indicating which element is in error. Programming is allowed

during this time.

PLATEN DOWN ERROR:

...occurs if the platen does not reach the proper position in 40

seconds or fails to move during this time. There is an audio

alarm with this message.

To cancel the message, press .

PLATEN UP ERROR:

...occurs if the platen is below the lower limit and does not

move for 40 seconds.

To cancel the audio alarm press .

HEATING ERROR:

...occurs when the controller does not detect a proper

temperature response over a six minute period. The

corresponding tri-color LED will turn red indicates which

element is in error.

COMM ERROR:

...occurs when there is no communication between the

control board and the motor board.

Press to reset the message and silence the beep.

MOTOR OVER CURRENT:

...displayed when the platen has been mechanically resisted.

The platen will stop and move to the lower limit. Press the

GREEN/CANCEL button to eliminate this display.

MOTOR ERROR:

...occurs when the platen is going up or down and does not

get 5 encoder counts in 1 second when the platen is below

the lower limit moving down or above the lower limit going

up. At this message the display will flash and there will be an

audio alarm. To cancel the message the power switch must

be recycled.

IGNITION ERROR:

...occurs if the ignition feedback signal does not give the

proper signal after four tries.

FLASHING LED(S):

...occurs after a failure for the ignition module to ignite

the gas. The grill LED will flash while the control tries

again. If successful the LED will continue to flash until set

temperature is reached and then turn to a solid green.

Содержание XE362S-2L

























































































Результаты поиска

Содержание XE362S-2L

Отзывы:

Похожие инструкции для XE362S-2L

Бренды по названию

Популярные бренды

Garland XE362S-2L, Руководство по обслуживанию

Результаты поиска

Содержание XE362S-2L

Отзывы:

Похожие инструкции для XE362S-2L

Бренды по названию

Популярные бренды