Garland MASTER SERIES XG24CE GB/IE, Руководство по установке и эксплуатации

Страница: 15 / 32

Part # 4517127 (06/23/08) Page 15
CLEANING AND MAINTENANCE continued
13. Starting at the back of the lower grill, spread a light
coating of grill cleaner over the entire surface. DO NOT
SCRUB.
14. After applying the grill cleaner, lightly scrub the grill
surface with the No-Scratch Pad until all the soil has been
liquefied.
15. Rinse the upper platens with a dripping wet cloth.
16. Carefully pour small quantities of lukewarm water
onto the grill while brushing the surface, backsplash,
and bullnose with a pot brush or equivalent high-
temperature brush. Continue until the water no longer
boils away and the grill remains wet. Squeegee dry.
Caution: Ice, cold water, or large quantities of water must
never be applied to the grill plate or upper platen. Severe
damage to the grill will occur!
17. Clean the release sheets as follows:
A) Place the sheets on the lower grill. Scrub both sides
of the sheets with the same no-scratch pad used on
the grill.
B) Rinse both sides of the sheets with a clean, wet cloth.
18. Rinse the lower grill by flooding the surface twice with
lukewarm water. Squeegee after each rinse.
19. Wipe the lower grill surface, backsplash, bullnose, and
hood with a clean, damp cloth.
20. When cleaning is completed, you may turn the “MASTER
POWER” (rocker) switch off.
AFTER CLEANING,
apply a thin coat of fresh shortening
to the lower grill surface only. Wipe down the
surrounding areas. Empty, wash, rinse, and replace the
grease troughs.
Platen Zeroing:
Turn Master power switch “ON”, wait for controllers to display
“OFF”.
1. Press and hold for three, (3) seconds. “ENTER CODE”
will be displayed.
2. Using the Gap Setting buttons,
enter the
code, (1251). “ENTER CODE **** ” will be displayed.
3. Press to enter the Programming Mode.
“PROGRAMMING MODE MENU ITEMS” will be displayed.
4. Press two, (2) times in succession to display
“PROGRAMMING MODE SYSTEM SETUP.”
5. Press six, (6) times. “PLATEN SET +/- XX” will be
displayed. (XX=numbers that will vary from grill to grill.)
6. Allow time for grill to heat and turn ready. Press
both the Cancel (Green) and Standby (Black) buttons
simultaneously to lower the upper platen. Press the
Cancel (Green) button to raise the platen. Now, press
both the Cancel (Green) and (Black) Buttons to re-lower
the platen.
7. Remove platen adjuster caps from all four adjustment
points on each platen. Remove the four locking caps from
the adjustment points.
8. Using the adjusting tool lower platen until adjusting tool
touches the arm assembly.
9. With gapping tool, adjust right rear of platen until the
gapping tool fits snugly between the upper platen and
grill surface.
10. Move next to the left front adjuster and raise the platen
until the gapping tool fits snugly between the upper
platen and grill surface.
11. Next go to the left rear adjuster and raise the platen until
the gapping tool fits snugly between the upper platen
and grill surface.
12. Move next to the right front adjustment and raise the
platen until the gapping tool fits snugly between the
upper platen and grill surface.
13. Repeat steps 9-12 one or more times until gapping tool
fits snugly between the upper platen and grill surface at
all four adjustment points without further adjustment.
(See diagram below.)
14. Replace the platen adjuster locking caps “hollow side
down” and tighten snugly. Replace platen adjuster caps.
15. Repeat steps 9-14 for each platen.
Insert gap tool directly below platen adjusters.