Gardsman IC2020, Руководство пользователя

Страница: 8 / 35

5
2. Learn-in the Devices
There are 2 Methods to learn in the device:
1. Using the Learning Mode, you can learn in
Pendant #1 and Pendant #2.
2. Use Command #91 - #94 in Programming
mode, you can learn in up to 10 devices
including PIR Sensor, Smoke Detector,
Panic Button, Carbon Monoxide, Wrist &
Neck Transmitter, Water Sensor, and
Pendant Transmitter. Please refer to
section
3.2 Programming Your IC2020:
Commands 91-94 .
z
Learning Mode:
Learning Mode is only used to learn and
remove Pendant #1 & Pendant #2 for IC2020.
2.1. Learning Pendant #1:
Step 1. Press the Nurse & Emergency Button
and hold these two buttons for 6 secs
to enter to Learn mode
Step 2. Once pressed, a button beep sound
will be heard. IC2020 will emit 2 beeps
when it reaches 6 sec.
Step 3. Release the button after you heard the
double beep . Then, IC2020 is now in
Learning Mode . The RED LED
begins to flash.
Step 4. Press both the NURSE and Pendant
#1 buttons simultaneously until
IC2020 emits a double-beep to
indicate that the Pendant #1 has been
learnt-in successfully.
<
<
N
N
O
O
T
T
E
E
>
>
)
It is prohibited to learn-in the same
Pendant twice (IC2020 will emit a long
beep instead of double-beeps).
)
Users can replace the learnt-in
Pendant in IC2020 with anohter
Pendant. The previous learnt-in
Pendant will become unfunctional.
Step 5. Carry the Pendant & walk around
your house. Press the
Pendant
button as you move and observe the
maximum range for its operation.
If IC2020 responds with one long
beep, the Pendent is within the
operation range.
If no signal is received within 30 sec,
IC2020 will exit Learning mode.
Step 6. If there is a 2
nd
Pendant (Pendant #2)
wished to be learnt-in, proceed to
Steps 3 - 5 under the section
Learning Pendant #2 .
Step 7. Otherwise, press both NURSE &
EMERGENCY buttons at the same
time to exit Learning Mode.
Or, if no signal is received within 30
sec, IC2020 will exit Learning mode.
IC2020 will emit a short beep and the
Red LED turns off to indicate the
system is back to Idle mode.
2.2. Learning Pendant #2:
Step 1. Press the Nurse & Emergency Button
and hold these two buttons for 6 secs
to enter to the Learn mode
Step 2. Once pressed, a button beep sound
will be heard. IC2020 will emit 2 beeps
when it reaches 6 sec.
Step 3. Release the button after you heard the
double beep . Then, IC2020 is now in
Learning Mode . The RED LED
begins to flash.
Step 4. Press both the EMERGENCY and
Pendant #2 buttons simultaneously
until IC2020 emits a double-beep to
indicate that the Pendant #2 has been
learned-in successfully.
<
<
N
N
O
O
T
T
E
E
>
>
)
It is prohibited to learn-in the same
Pendant twice (IC2020 will emit a long
beep instead of double-beeps).
)
User can replace the learnt-in
Pendant in IC2020 with another
Pendant. The previous learnt-in
Pendant will become unfunctional.
Step 5. Carry the Pendant & walk around
your house. Press the
Pendant
button as you move and observe the
maximum range for its operation.
If IC2020 responds with one long
beep, the Pendent is within the
operation range.
If no signal is received within 30 sec,
IC2020 will exit Learning mode.