background image

 

3-1-618    Page 1 

SECTION 1 
DANGER NOTICES 

 

   

DANGER 

Read and understand the following DANGER 

 

NOTICES before moving or operating the pump or 
any pump package unit equipment. 

 
Reciprocating pumps are machines capable of 
producing high fluid pressures and flow rates and 
are designed to be used with proper care and 
caution by trained, experienced operators.  

TO 

AVOID PERSONAL INJURY, DEATH AND/OR 
EQUIPMENT DAMAGE, READ AND 
THOROUGHLY UNDERSTAND THE 
FOLLOWING DANGER NOTICES PLUS THE 
ENTIRE OPERATING AND SERVICE MANUAL 
BEFORE ATTEMPTING TO MOVE OR OPERATE 
THE PUMP

.  Contact a Gardner Denver  service 

representative if you are unable to comply with any 
of the danger notices or procedures described in 
these documents. 

 
Closely examine the data plate upon pump delivery 
to become thoroughly familiar with the operating 
limits for this pump model.  

The pump must never 

be operated at speeds, pressures or 
horsepower exceeding the maximum values 
shown on the data plate or at speeds below the 
minimum shown.  Failure to observe the 
operating limits shown on the data plate could 
result in personal injury, death, and/or 
equipment damage and will void the warranty

.  

Alterations to the pump, or application of the pump 
outside the data plate limits, must not be made 
without Gardner Denver written approval together 
with a new data plate, as dangerous operating 
conditions could result. 
 
THE DANGER NOTICE AND DATA PLATES 
PROVIDED ON THE EQUIPMENT MUST NOT BE 
REMOVED, PAINTED OVER, HIDDEN OR 
DEFACED.  They must be replaced if they become 
damaged or unreadable.  Provisions should be 
made to have the following written danger notices 
plus the pump operating and service manual readily 
available to operators and maintenance personnel.  
In addition, copies of all pump system accessory 
component (e.g. pressure relief valve, pulsation 
dampener, suction stabilizer, engine, electric motor, 
etc.) operating and service manuals should be 
readily available for operator and maintenance 
personnel use.  Read and follow all the precautions 
and instructions contained in these manuals.  If any 
of these documents are lost or become illegible 
they must be replaced immediately.  The danger 

notices plus the operating and service manuals 
should be reread periodically by both operators and 
maintenance personnel to refresh their memories in 
safe procedures and practices. 

 

Keep in mind that full operator attention and 
alertness are required when operating high 
pressure pumping equipment.  Operators 
should not begin or continue operations when 
tired, distracted or under the influence of 
alcohol or any type of prescription or 
nonprescription drugs. 

 
The timely replacement of expendable parts and 
any other worn or damaged parts can prevent 
equipment damage and possible injury.  The 
original parts used in Gardner Denver pumps are 
designed and tested to exacting standards to 
provide high quality performance and durability.  
Your best insurance in maintaining these 
characteristics is to use genuine Gardner Denver 
replacement parts. 

 
A broad range of danger notices are covered on 
these pages, however, they cannot substitute for 
training, experience and common sense in the safe 
operation of high pressure pumping equipment. 

 

 

HAMMER LUG FASTENERS 

   

DANGER 

On pumps or pump package units equipped with 
hammer lug connectors and/or hammer lug valve 
covers the following precautions must be observed 
to avoid personal injury, death and/or equipment 
damage due to contact with the hammer, hammer 
bar, broken parts from the hammer, hammer bar or 
lugs or other objects propelled by hammer blows.  
When tightening or loosening hammer lug 
connectors and valve covers, operators or 
maintenance personnel should: 

 

•  Inspect the hammer, hammer lugs and 

hammer bar, if one is used, to insure they 
are all in good condition.  Replace any of 
these parts which are cracked, damaged or 
badly worn. 

 

• 

Wear safety shoes and goggles. 

 

• 

Alert other personnel to move away from the 
area. 

 

• 

Check to insure they have safe footing. 

Содержание GD-250



































Отзывы: