13-9-663 Page 19
AFTERCOOLER
Water Temperature to Heat
Exchanger
Gallons/minute
HP Model
60
°
F
70
°
F
80
°
F
90
°
F
Maximum Water
Flow
Gallons/minute *
Approximate Water
Pressure Drop @ 90
°
F
Water Temperature PSI
40
EAH99C
EBH99G
.5 .7 .9 1.3
26.0
50
EAH99C
EBH99G
.7 .9 1.2 1.8
26.0
60
EAM99C
EBM99K
.8 1.0 1.4 2.1
26.0
75
EAM99C
EBM99K
1.2 1.5 2.0 3.0
26.0
100
EAP99J
EBP99J
ERH99E
1.7 2.1 2.8 4.1
26.0
Less than 1 PSI for any
flow rate shown in the table
* Flows exceeding "Maximum Water Flow" will cause severe erosion and will void unit warranty.
AFTERCOOLER (INTERNATIONAL)
Water Temperature to Heat
Exchanger
Liters/seconds
KW Model
16
°
C
21
°
C
27
°
C
32
°
C
Maximum
Water Flow
Liters per
Second *
Approximate Water
Pressure Drop @ 32
°
C
Water Temperature (bar)
45 EBM99L
.05 .06 .09 .13
3.47
56 EBM99L
.08 .09 .13 .19
3.47
75 EBM99L
.11 .14 .19 .28
3.47
Less than .1 bar for any flow
rate shown in the table
* Flows exceeding "Maximum Water Flow" will cause severe erosion and will void unit warranty.
Figure 2-6 – AFTERCOOLER APPROXIMATE WATER FLOW
WATER PIPING (Water-Cooled Heat Exchanger Models Only)
- On machines equipped with water-
cooled heat exchangers, the water inlet and outlet connections are located in the unit base flange on the
left side of the unit.
It is mandatory that any water cooled unit be installed in a shelter heated to
temperatures above freezing (32
°
F., 0
°
C).
The water source should be capable of supplying up to the maximum flow shown in
Figure 2-5
, page 18, and
Figure
2-6
, page 19, at a minimum pressure of 40 psig (2.8 bar); maximum allowable water pressure is
150 psig (10.3 bar). The water flow rates shown are approximate and a guide to sizing piping, cooling
tower and other water system equipment.
The heat exchanger system is designed to operate with water inlet temperatures from 60
°
F to 90
°
F (16
°
C to 32
°
C) and a water outlet temperature not to exceed 110
°
F (43
°
C). If water cooler than 60
°
F is
used, high water outlet temperatures (over 110
°
F, 43
°
C) will be experienced along with shortened heat
exchanger life caused by tube fouling and corrosion. If water warmer than 90
°
F (32
°
C) is used, higher
compressor oil inlet temperatures and high water usage will result.
C
C
C
A
A
A
U
U
U
T
T
T
I
I
I
O
O
O
N
N
N
Содержание EAH99C
